manualshive.com logo in svg

Siemens ERTEC 200P, Manual

The Siemens ERTEC 200P is a cutting-edge device designed for industrial communication networks. To easily set up and configure this powerful product, you can find a comprehensive user manual available for free download on our website. Unlock the full potential of the ERTEC 200P with our detailed manual at 88.208.23.73:8080.

Share
Download
background image

 
 

 

Copyright © Siemens AG 2016. All rights reserved 

62 

ERTEC 200P-2 Manual 

Technical data subject to change 

 

Version  1.0 

 

Furthermore there is following problem: If the ICU assigns an interrupt and the software 
acknowledges it followed by a “fast” EOI (fast means, that the EOI is issued 1-3 operating 
clock cycles after acknowledge), the ICU outputs a new interrupt due to internal hardware 
latencies. This new interrupt is deleted again after a few clock cycles. When the CPU 
acknowledges this interrupt it will read the default vector. This scenario is only a perfor-
mance issue but not a functional one. Besides it is currently not known that any CPU is 
as fast as to perform such a fast EOI after acknowledge. 

Deletion of interrupts during the reset phase 

If the ICU is in reset and there are already high levels pending at the interrupt inputs 
when the ICU comes from the reset phase, these high levels are evaluated as rising edge 
by the edge detection as regards the hardware and an interrupt is immediately entered in 
the interrupt request register (since edge-triggering to the positive edge is set by default 
during the reset). This is not a valid interrupt and has to be deleted again immediately by 
the software by writing on INTA_IRCLVEC or INTB_IRCLVEC. 

Procedure for locking priorities via LOCKREG 

Since it takes a certain latency from the issuing of the software write to LOCKREG until 
the register in the hardware is actually written on, it is reasonable to read back the 
LOCKREG register again immediately. Only when the read-back value returns to the 
CPU (it does not have to be checked if the register value is correct, it is just about the 
waiting), can one be sure that no more interrupts are triggered which have a lower priority 
than the priority which was entered in the LOCKREG register. Apart from that, there are 
no other specialties to be observed for the writing on the register, it can be written on at 
any time. 

 

2.3.2.13.5  Startup/shutdown 

After the reset, all interrupts are deactivated (dedicated mask bits set as well as the glob-
al mask bit, if any). The priority of each interrupt is the lowest priority which can be as-
signed. This means that for initializing the ICU, all interrupts have to be assigned an own 
priority first before the mask bit is released. Before releasing the interrupts, it should also 
be determined which interrupts are level/edge-triggered and stated which edge is the 
active one, if necessary. If a priority locking is to be carried out, this has to be configured 
correctly and activated before. 

Furthermore, it has to be taken into account that INTAs as well as INTBs are edge-
triggered by default. If level-triggering is set, the interrupt has to be canceled at the 
source. Otherwise, it triggers a new interrupt (INTA or INTB) at the CPU after the 
acknowledgement. 

The INTA applied to the INTB always has to be set to the same triggering. This is not 
checked by the ICU and has to be ensured by the software. Moreover, the SW should 
normally mask the INTA input in the INTA sub-block used as INTB since otherwise an 
INTA as well as an INTB is signaled to the CPU upon the occurrence of the interrupt. 

 

Summary of Contents for ERTEC 200P






















































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERTEC 200P

Raymarine P70 Quick Reference preview
P70
Brand: Raymarine Pages: 12
Jafar 2005 Operation And Maintenance Manual preview
2005
Brand: Jafar Pages: 13
TCS Basys Controls QD Series Troubleshooting Worksheet preview
QD Series
Brand: TCS Basys Controls Pages: 2
Saitek X36 Manual preview
X36
Brand: Saitek Pages: 4
Camozzi PRE Series Operation And Maintenance Instructions preview
PRE Series
Brand: Camozzi Pages: 33
Camozzi K8 Series Use And Maintenance Instructions preview
K8 Series
Brand: Camozzi Pages: 2
Camozzi PME Series Operation & Maintenance Instructions Manual preview
PME Series
Brand: Camozzi Pages: 64
Olimpia splendid SHERPA MONOBLOC B0812 Owner'S Manual preview
SHERPA MONOBLOC B0812
Brand: Olimpia splendid Pages: 44
Olimpia splendid B1012 Installation And Maintenance Instruction preview
B1012
Brand: Olimpia splendid Pages: 44
Olimpia splendid Bi2 B0772 Instructions Manual preview
Bi2 B0772
Brand: Olimpia splendid Pages: 16
Balboa BP600 Tech Sheet preview
BP600
Brand: Balboa Pages: 23
Balboa VL260 Quick Reference Manual preview
VL260
Brand: Balboa Pages: 2
Parker TFP Series Operation Manual preview
TFP Series
Brand: Parker Pages: 16
ZKTeco SRB Connection Manual preview
SRB
Brand: ZKTeco Pages: 2
National Instruments PXI-8150B User Manual preview
PXI-8150B
Brand: National Instruments Pages: 78
Vizio Xrt302 Manual preview
Xrt302
Brand: Vizio Pages: 65
Matelec FPC-36040 Owner'S Operation Manual preview
FPC-36040
Brand: Matelec Pages: 16
Coris OMM-120-15 Quick Start Manual preview
OMM-120-15
Brand: Coris Pages: 4

Brands by name

Popular brands

Load more brands