12
AL110/AL110A / UK / A31008-M2303-L101-1-7619 / main.fm / 07.06.2011
Standard characters
1) Space
Specifications
Recommended batteries
Nickel-metal-hydride (NiMH)
V30145-K1310-X383
(Valid at the time of going to press)
The handset is supplied with recommended
batteries.
Base station power consumption
General specifications
Questions and answers
If you have any queries about the use of your tele-
phone, visit our website at
www.gigaset.com/uk/service
for 24-hour support. The table below contains a list of
common problems and possible solutions.
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x11x12x13x14x
1
1
£
$
¥
¤
2
a
b
c
2
ä
á
à
â
ã
ç
I
d
e
f
3
ë
é
è
ê
4
g
h
i
4
ï
í
ì
î
5
j
k
l
5
L
m
n
o
6
ö
ñ
ó
ò
ô
õ
M
p
q
r
s
7
ß
N
t
u
v
8
ü
ú
ù
û
O
w
x
y
z
9
ÿ
ý
æ
ø
å
Q
.
,
?
!
0
+
-
:
¿
¡
"
’
;
_
P
*
/
(
)
<
=
> %
#
Abc
-->
123
123
-->
abc
#
@
\
&
§
AL110
AL110A
In standby mode
– Handset in base station
– Handset outside base station
ca. 1,0 W
ca. 0,8 W
ca. 1,2 W
ca. 1,0 W
During a call
ca. 1,0 W
ca. 1,2 W
DECT standard
is supported
GAP standard
is supported
(the Gigaset handset ope-
rates only with a Gigaset
base)
Range
up to 300 m outdoors
up to 50 m indoors
Base station power supply
230 V ~/50 Hz
Environmental conditions
in operation
+5 °C to +45 °C, 20% to
75% relative humidity
1)
Problem
Cause
Solution
Nothing
appears in
the display.
The handset is not
switched on.
The batteries are
flat.
Press the end call
key
a
for
approx.
5 seconds
or place the
handset in the base
station.
Charge or replace the
batteries.
No wireless
connection
to the base sta-
tion,
Base
flashes in
the display.
The handset is out-
side the range of
the base station.
The handset is not
registered.
The base station is
not turned on.
Move the handset
closer to the base
station.
Register the handset
¢
p. 10.
Check the mains con-
nector on the base sta-
tion
¢
p. 3.
You cannot
hear a ringer/
dialling tone
from the fixed
line network.
The phone cord
supplied has not
been used or has
been replaced by a
new cord with the
wrong jack con-
nections.
Please always use the
phone cord supplied or
ensure that the
pin connections are
correct when purchas-
ing from a retailer:
3-4 assignment of
telephone leads/
EURO CTR37.
Error tone
sounds after
system PIN
prompt.
PIN forgotten.
The system PIN you
have entered is
incorrect.
Reset the system PIN to
the default 0000
¢
p. 11.
All handsets are
de-registered. All set-
tings are reset. All lists
are deleted.
