background image

75

Using several handsets

Gigaset S675 IP / IM-NORD EN / A31008-M1915-R201-1-PG19 / T-NetBox_SAG-registration.fm / 6.8.07

Ve

rs

ion 4,

 16

.09.

2005

If you accept an incoming call, the room 

monitor is suspended for the duration of 

the call, but the function 

remains

 acti-

vated.
If you deactivate then re-activate the 

handset, the room monitor remains acti-

vated. 

Activating the room monitor and 

entering the number to be called

v

  

¢

í

 

¢

Room Monitor 

¤

Change multiple line input: 

Room M.:

Select 

On

 to activate.

Call to:

External number:

 

¤

Select the number from the direc-

tory (press display key 

Ò

) or 

enter it directly. Only 

the last 4 

characters

 are displayed.

Internal number:

 

¤

Press the display key 

§Options§

.

Select 

INT

 and press 

§OK§

.

¤

Use 

s

 to select the handset or 

Call 

All 

(if all registered handsets are to 

be called) and press

§OK§

.

Level:

Set noise level sensitivity (

Low

 or 

High

).

¤

Save changes (page 127).

The function is now activated. With 

v

you can move directly to settings.

Changing the set destination number

v

 

¢

í

 

¢

Room Monitor 

s

Scroll to the 

Call to:

 line.

X

 or 

§Delete§

Delete existing number.

¤

Enter number as described in "Activat-

ing the room monitor and entering the 

number to be called" (page 75).

Deactivating the room monitor 

remotely

Precondition

: The room monitor call is 

sent to an external destination number. 

The telephone called supports touch tone 

dialling.

¤

Accept the call from the room monitor 

and press keys 

9

 

;

Your base station sends a confirmation 

tone and ends the connection. 

Room monitor function deactivated on 

handset. There will be no further room 

monitor calls. The other room monitor set-

tings (e.g. no ringer tone) on the handset 

will remain activated until you press the 

display key 

§OFF§

 on the handset. 

To re-activate the room function with the 

same phone number:

¤

Turn on the activation again and save 

with 

§Save§

 (page 75). 

Warning!

You should always check the operation 

of the room monitor before use. For 

example, test its sensitivity. Check the 

connection if you are diverting the room 

monitor to an outside number.

 

– When the function is switched on, the 

handset's operating time is considerably 

reduced. If necessary, place the handset in 

the charging cradle. This ensures that the 

batteries do not run down.

– Ideally the handset should be positioned 1 

to 2 metres away from the baby. The micro-

phone must be directed towards the baby. 

– The connection to which the room monitor 

is forwarded must not be blocked by an 

activated answer machine.

Please note: 

If you do not specify a line suffix (page 25) and 

you do not define any dialling plans for the 

number (page 109), an external number will 

be dialled via the set standard connection 

(VoIP or fixed line network). 

Please note:

External deactivating via VoIP connections is 

possible as long as the DTMF signals are trans-

mitted (depending on the provider) either as 

SIP info messages, audible signals in the voice 

channel (inband or audio) or as special RTP 

data packets (pursuant to RFC2833). 

Summary of Contents for Gigaset S675IP





































































































































































Reviews: