10
Changing the basic settings
Your oven has various basic settings. These settings can be
customised to suit your requirements.
No other time-setting option should have been set.
1.
Press and hold the
0
button for approx. 4 seconds.
The current basic setting for the clock display is shown in the
display, e.g. c1 1 for selection 1.
2.
Use the
@
or
A
button to change the basic setting.
3.
Confirm by pressing the
0
button.
The next basic setting appears in the display. You can scroll
through all levels with the
0
button and change the setting
with the
@
or
A
button.
4.
To finish, press and hold the
0
button for approx. 4 seconds.
All basic settings are applied.
You may change the basic settings at any time.
Care and cleaning
If cleaned and properly cared for, your oven will keep its bright
appearance and operating performance for many years to
come. Advice on how to care for and clean your oven is
provided below.
Notes
■
Different colours may be seen in your front panel due to the
various materials used in its manufacture, such as glass,
plastic and metal.
■
Dark patches in the door's glass panel may seem to be dirt
but they are in fact reflections from the oven light.
■
Enamel burns at very high temperatures. This may cause
slight discolouration. This is normal and does not affect the
oven's operation. The edges of thin baking trays may not be
completely enamelled. They may therefore feel slightly rough,
although their corrosive protection will be unaffected.
Cleaning products
To ensure that the different surfaces are not damaged by using
the wrong cleaning product, follow the instructions in the table.
Do not use
■
Aggressive or abrasive cleaning agents,
■
Cleaning agents with a high alcohol content,
■
Hard scouring pads or sponges,
■
High-pressure cleaners or steam cleaners.
Wash new tea towels thoroughly before use.
Light
The oven light can be turned on manually to facilitate cleaning.
Turning on the oven light
Turn the function control knob to the
\
setting.
The light will come on. The temperature control knob must be
turned off.
Turning the oven light off
Turn the function control knob to the
Û
position.
Basic setting
Selection 1 Selection 2 Selection 3
c1
Clock display
always*
only with
the
0
but-
ton
-
c2
Signal duration
upon completion of
a cooking time or
timer period
approx.
10 seconds
approx.
2 minutes*
approx.
5 minutes
c3
Waiting time until a
setting is applied
approx.
2 seconds
approx.
5 seconds*
approx.
10 seconds
* Factory setting
Area
Cleaning products
Oven front
Hot soapy water:
Clean with a dish cloth and dry with a soft
cloth. Do not use glass cleaner or glass
scrapers for cleaning.
Stainless
steel
Hot soapy water:
Clean with a dish cloth and dry with a soft
cloth. Remove flecks of limescale, grease,
starch and albumin (e.g. egg white) immedi-
ately, as rust can form underneath them.
Special stainless steel cleaning products
suitable for hot surfaces are available from
our after-sales service or from specialist
retailers. Apply a very thin layer of the clean-
ing product with a soft cloth.
Glass
Glass cleaner:
Clean with a soft cloth. Do not use a glass
scraper.
Display
Glass cleaner:
Clean with a soft cloth. Do not use alcohol,
vinegar, or any other aggressive or abrasive
cleaning agents.
Door panels
Glass cleaner:
Clean with a soft cloth. Do not use a glass
scraper.
Oven carriage
floor
Hot soapy water or a vinegar solution:
Clean with a dish cloth.
Cooking com-
partment
Hot soapy water or a vinegar solution:
Clean with a dish cloth.
Use stainless steel wire wool or oven
cleaner to remove stubborn dirt. Use only
when the cooking compartment is cold.
Glass cover for
the oven light
Hot soapy water:
Clean with a dish cloth.
Seal (do not
remove)
Hot soapy water:
Clean with a dish cloth. Do not scrub.
Accessories
Hot soapy water:
Soak and clean with a dish cloth or brush.
Area
Cleaning products
Summary of Contents for HE23BC 0 Series
Page 1: ... HQ QVWUXFWLRQ PDQXDO XLOW LQ RYHQ ...
Page 23: ......
