Siemens LB 23 Operating And Installation Instructions Download

Page: 15 / 16

Remove the

filter grille

(see operating

instructions).

Connect the

power.

Press the

extractor hood

up into the

installation opening until the installation
aid locks into position at the front and
rear.

Screw in the

extractor

hood.

Insert and secure the

filter grille

(see

operating instructions).

Loosen the screws.

2. Hold the underside of the extractor

hood,

Hold the underside of the extrac-

tor hood.

Lower the

extractor hood

and remove.

Installation

Installation spring

Weight in kg:

Width

53 cm

1-motor

Rocker switch

Design changes with respect to technical development
shall remain withheld

Model

Exhaust

air

Recircu

lated air

5,0

6,3

1-motor

Slide control

1-motor

Slide control

53 cm

73 cm

2-motor

Slide control

2-motor

Slide control

53 cm

73 cm

9,5

8,3

8,7

10,7

9,5

9,9

Removal

10,3

11,6

9000.022 567.qxd 06.09.2006 11:36 Uhr Seite 15

Summary of Contents for LB 23

















Search results

Summary of Contents for LB 23

Reviews:

Related manuals for LB 23

Brands by name

Popular brands

Siemens LB 23, Operating And Installation Instructions

Search results

Summary of Contents for LB 23

Reviews:

Related manuals for LB 23

Brands by name

Popular brands