background image

 Trouble shooting  

en

9

3

Trouble shooting

Trouble s

hooting

Malfunctions often have simple explanations. Please 

read the following notes before calling the after-sales 

service.

:

Warning

Risk of electric shock!

Incorrect repairs are dangerous. Repairs may only be 

carried out and damaged power cables replaced by 

one of our trained after-sales technicians. If the 

appliance is defective, unplug the appliance from the 

mains or switch off the circuit breaker in the fuse box. 

Contact the after-sales service.

Malfunction table

--------

LED lights

Defective LED lights may be replaced by the 

manufacturer, their customer service or a qualified 

technician (electrician) only.

:

Warning

Risk of injury!

The light emitted by LED lights is very dazzling, and can 

damage the eyes (risk group 1). Do not look directly 

into the switched on LED lights for longer than 100 

seconds.

4

Customer service

Customer 

service

When calling us, please quote the product number (E 

no.) and the production number (FD no.) so that we can 

provide you with the correct advice. These numbers can 

be found on the rating plate on the top of the appliance.

You can make a note of the numbers of your appliance 

and the telephone number of the after-sales service in 

the space below to save time should it be required.

Please be aware that a visit by an after-sales engineer 

will be charged if a problem turns out to be the result of 

operator error, even during the warranty period.
Please find the contact data of all countries in the 

enclosed customer service list.

To book an engineer visit and product advice

Rely on the professionalism of the manufacturer. You 

can therefore be sure that the repair is carried out by 

trained service technicians who carry original spare 

parts for your appliances.

Problem

Possible cause Solution

The appliance 

does not work

The plug is not 

plugged in.

Connect the appliance to the 

electricity supply

Power cut

Check whether other kitchen 

appliances are working

Faulty fuse

Check in the fuse box to make 

sure that the fuse for the 

appliance is OK

The lighting does 

not work.

The LED lights 

are defective.

Call the after-sales service.

The button illumi-

nation does not 

work.

The control unit is 

faulty.

Call the after

­

sales service.

E no.

FD no.

After-sales service

O

GB

0344 892 8999 

Calls charged at local or mobile rate.

IE

01450 2655 

0.03 € per minute at peak. Off peak 0.0088 € 

per minute.

=1U

)'

(1U

7\SH

Summary of Contents for LC67KHM60





















Reviews: