background image

7

INSTALLATION INSTRUCTIONS

Installation instructions

This appliance is installed on the wall.

Follow the enclosed installation instructions for additional 

special accessories (e.g. for circulating-air mode).

The surfaces of the appliance are sensitive. Avoid damaging 

them during installation. 

Safety information

Danger to life! Risk of poisoning!

from combustion gases sucked back in. Never operate the 

appliance in the exhaust air mode at the same time as a room 

air-dependent heat-producing appliance unless an adequate 

supply of fresh air is ensured.

Room air-dependent heat-producing appliances (e.g. gas, oil, 

wood or coal-operated heaters, continuous flow heaters or 

water heaters) obtain combustion air from the room in which 

they are installed and discharge the exhaust gases into the 

open through an exhaust gas system (e.g. a chimney).
In combination with an activated vapour extractor hood, room 

air is extracted from the kitchen and neighbouring rooms - a 

partial vacuum is produced if not enough fresh air is supplied. 

Toxic gases from the chimney or the extraction shaft are 

sucked back into the living space.

Adequate incoming air must therefore always be ensured.

An incoming/exhaust air wall box alone will not ensure 

compliance with the limit.

Safe operation is possible only whenever the partial vacuum in 

the place where the firing equipment is installed does not 

exceed 4 Pa (0.04 mbar). This can be achieved whenever the 

air needed for combustion is able to enter through openings 

that cannot be sealed, for example in doors, windows, 

incoming/exhaust air wall boxes or by other technical means.

In any case, consult your responsible chimney sweep. He is 

able to assess the house's entire ventilation setup and will 

suggest the suitable ventilation measures to you.
Unrestricted operation is possible if the vapour extractor hood 

is operated exclusively in the recirculation mode.

Risk of fire!

from flying sparks. Do not install the appliance above a solid 
fuel heater (e.g. wood or coal) unless a closed, non-removable 
cover is available.
For the installation, observe the currently valid building 

regulations and the regulations of the local electricity and gas 

suppliers.

Risk of electric shock!

from damaged connection cable. Do not kink or pinch 
connection cable during installation.

Risk of injury!

From sharp edges during installation. Always wear protective 
gloves while installing the appliance.

Risk of injury!

from a falling appliance. All safety screws and safety caps must 
be firmly fitted.

PP

PP

!

!

[

[

[

[

[

[

[

[

[

Summary of Contents for LC98BC540













Reviews: