Siemens LF259RB51, Instruction Manual

Operating the appliance       

en

7

Connecting the remote control to the appliance

If the appliance cannot be operated with the remote 

control, e.g. after the battery has been changed, the 

connection between the remote control and the 

appliance must be re-established.

1.

Press and hold the 

@

 button.

2.

Attach the appliance to the mains voltage.

A long audible signal sounds. The remote control 

has been connected to the appliance.

Note: 

If no audible signal sounds within 30 seconds, 

repeat this procedure.

Extractor hood's control panel

Operating buttons

Setting the fan

Note: 

Always adjust the setting according to the current 

conditions. To eliminate strong cooking smells, select a 

high fan setting.

Switching on

1.

Press the 

@

 button.

The fan will start at fan setting 

ƒ

.

2.

Press the 

@

 or 

 A

 button to set a different fan setting.

Note: 

The appliance has three fan settings and an 

intensive setting. To set the lowest setting, 

press 

A

 once. If you press it more than once, the 

appliance will switch off again.

Switching off

Press and hold the 

A

 button until the appliance 

switches off.

or

 press the 

$

 button.

Intensive setting

You can use the intensive setting if there is a large 

build-up of odours and fumes/vapours.

Press and hold the 

@

 button until 

˜

 appears in the fan 

settings display .

Note: 

Intensive mode runs for four minutes. Once this 

time has elapsed, the appliance will switch back to fan 

setting 

ƒ

.

Intermittent mode

Intermittent mode automatically switches on the 

extractor hood for 10 minutes every hour. The function 

switches itself off again after 24 hours.
This function can be activated from the control panel or 

using the remote control.

Note: 

If intensive mode or the run-on function has been 

activated, the intermittent function will not be available.

Switching on intermittent mode from the control panel

1.

Press the 

$

 and 

@

 buttons at the same time until 

‚

appears in the display.

2.

Press the 

@

 button. The following fan settings will 

appear in the display: 

ƒ

~

„

~

‚

~

ƒ

, etc. 

3.

Press the 

$

 and 

@

 buttons at the same time to 

confirm the fan setting for intermittent mode.

Switching on intermittent mode using the remote 

control

1.

Press the 

N

 button. 

‚

 will appear in the display.

2.

Press the 

@

 button. The following fan settings will 

appear in the display: 

ƒ

~

„

~

‚

~

ƒ

, etc.

3.

Press the 

N

 button to confirm the fan setting for 

intermittent mode.

Note: 

Pressing any of the buttons (except the button for 

the light) will deactivate intermittent mode.

Run-on function

The run-on function allows the extractor hood to 

continue running for a few minutes after it has been 

switched off. This eliminates any remaining cooking 

smells. The extractor hood will then switch itself off 

automatically.

Switching on

Note: 

If intensive mode has been activated, the run-on 

function will not be available.

Press the 

*

 button on the control panel or the 

+

button on the remote control.
The fan will run for 10 minutes at setting 

‚

 and a dot 

will flash in the display during this time. Then the fan will 

switch itself off automatically.

Switching off

Press the 

*

 or 

$

 button on the control panel or the 

+

 button on the remote control for the extractor hood.

This will deactivate the run-on function immediately.

(

Fan settings display 

0

Operating buttons

Explanation

=

Light on/off/dimming

$

Switches the extractor hood on and off

A

Decrease fan setting

@

Increase fan setting

*

Fan run-on