background image

 General information  

en

13

Electrical connection

:

Warning

Risk of electric shock!

Components inside the appliance may have sharp 

edges. These may damage the connecting cable. Do 

not kink or pinch the connecting cable during 

installation.

The required connection data can be found on the 

rating plate inside the appliance; to do this, remove the 

metal mesh grease filter.

Length of the cable: approx. 1.30 m

This appliance complies with the EC interference 

suppression regulations.

:

Warning

Risk of electric shock!

It must always be possible to disconnect the appliance 

from the power supply. The appliance must only be 

connected to a protective contact socket that has been 

correctly installed. If the plug can no longer be reached 

after installation, an energy-isolating device in the 

phases must be provided in the permanent electrical 

installation in accordance with the installation 

regulations. The permanent electrical installation must 

only be wired by a professional electrician. We 

recommend installing a residual-current circuit breaker 

(RCCB) in the appliance's power supply circuit.

Preparing the units

The fitted unit must be level and have sufficient load-

bearing capacity.

The max. weight of the extractor hood is 18 kg.

Appliance dimensions and safety clearances

Observe the appliance's dimensions.

Comply with the safety clearances.

If the installation instructions for the gas cooking 

appliances specify a different distance, the largest 

distance must always be provided for.

The fitted unit must be heat-resistant up to 90 °C. The 

fitted unit must still be sturdy after the cut-outs have 

been made.

To install an upper cabinet, this extractor hood must be 

provided with the following dimensions:

1.

Make the cut-out for the exhaust air pipe. To do this, 

make an opening in the ceiling or back wall of the 

fitted unit with an additional recess for the power 

cord.

2.

If the cabinet base is present, remove this. Mark the 

securing points on the inside of the cabinet and pre-

cut the holes using a piercer. Use the enclosed 

template to mark the securing points. 

¨

3.

Screw in the four enclosed screws for the angle 

bracket up to 5 mm. 

©

Width

600 mm

Depth

Min. 320 mm

Height

Min. 390 mm

PP

PP

Summary of Contents for LI64MA530

















Reviews: