background image

Operating modes    

en

5

Ç

Operating modes

Operating modes

Exhaust air mode

Note: 

The exhaust air must not be conveyed into a 

functioning smoke or exhaust gas flue or into a shaft 

which is used to ventilate installation rooms which 

contain heat-producing appliances.

Before conveying the exhaust air into a non-

functioning smoke or exhaust gas flue, obtain the 

consent of the heating engineer responsible.

If the exhaust air is conveyed through the outer wall, 

a telescopic wall box should be used.

Air recirculation

Note: 

To bind odours in air recirculation mode, you 

must install an activated carbon filter. The different 

options for operating the appliance in air recirculation 

mode can be found in the brochure. Alternatively, ask 

your dealer. The required accessories are available 

from specialist retailers, from customer service or from 

the Online Shop.

1

Operating the appliance

Operating the appliance

These instructions apply to several appliance variants. 

It is possible that individual features are described 

which do not apply to your appliance.

Note: 

Switch on the extractor hood when you start 

cooking and switch it off again several minutes after you 

have finished cooking. This is the most effective way of 

removing the kitchen fumes.

Control panel

Setting the fan

Switching on

Pull out the filter pull-out and press the 

#

 button. The 

fan starts at setting 2.
Press the + or - button to change the fan strength.

Switching off

Press the 

#

 button. Slide the filter pull-out in.

Intensive setting

You can use the intensive setting if there is a large 

build-up of odours and fumes/vapours.
Press the + button until all of the LEDs in the display 

light up. The intensive setting is activated. 
After approx. six minutes, the electronics automatically 

reduce the fan to a lower setting . If you want to end the 

intensive setting before the preset time expires, press 

the - button until the required fan setting is reached.
The run time is limited. The fan is then automatically 

reduced to a lower fan setting. You can switch back 

manually at any time.

Fan run-on time

If you slide in the filter pull-out, the run-on time will be 

activated for as long as the extractor hood is operating.
After approx. 10 minutes, the fan switches off 

automatically.

Lighting

The lighting can be switched on and off independently 

of the ventilation.
Press the 

A

 button.

The air which is drawn in is cleaned 

by the grease filters and conveyed to 

the exterior by a pipe system.

The air which is drawn in is cleaned by 

the grease filters and an activated 

carbon filter, and is conveyed back into 

the kitchen.

Explanation

<

Light on/off

#

Fan on/off

-

Reduces the fan speed

+

Increases the fan speeds/intensive setting

Summary of Contents for LI67SA530A

















Reviews: