background image

CC1N7138en 
18.05.2016 

 

Building Technologies Division

 

 

 

7

138

 

 

 

 

 

 

Oil Burner Controls 

LMO64...

 

 

Microcontroller-based oil burner controls for the startup, supervision and control 
of forced draft oil burners in intermittent operation. Maximum oil throughput up 
to 30 kg/h. 
 
The LMO64... and this Data Sheet are intended for use by OEMs which integrate 
the burner controls in their products. 

Use, features 

The LMO64... burner controls are designed for the startup and supervision of 1-stage 
forced draft oil burners in intermittent operation. Yellow-burning flames are supervised 
with photo resistive detectors QRB..., blue-burning flames with blue-flame detectors 
QRC... 
 

 

Applications in accordance with EN 267: 

Automatic forced draft burners for liquid 

fuels

 

 

Type-tested and approved in accordance with DIN EN 298 

 

 

Undervoltage detection 

 

Electrical remote reset 

 

Bridging contact for oil preheater 

 

Monitoring of time for oil preheater 

 

Accurate and reproducible program sequence through digital signal handling 

 

Controlled intermittent operation after 24 hours of continuous operation 

 

Limitation of the number of repetitions 

 

Multicolor indication of fault and status messages 

 

 

Postpurge function for clearing the combustion chamber after burner operation 

Use 

General features 

Specific features 

Summary of Contents for LMO64 Series

















Reviews: