en
Before using for the first time
6
Before using for the first time
Configure the settings for initial start-up. Clean the ap-
pliance and accessories.
Basic operation
You can find out everything you need to know about
operating your appliance here.
Switching on the appliance
Requirement:
Align the remote control as precisely as
possible to the infrared receiver for the LED display.
▶
Press to switch on the appliance.
a
The appliance starts at fan setting 2.
a
The LED for the set fan setting lights up in the LED
display.
Switching off the appliance
Switch the appliance off when you are not using it.
▶
Press .
a
The fan run-on is switched on, LED 6 flashes in the
LED display for the fan run-on.
a
The fan automatically switches off after approx. 10
minutes.
Selecting a fan setting
▶
Press or .
a
The LED for the set fan setting lights up in the LED
display.
Switching on intensive mode
If particularly strong odours or vapours develop, you
can use intensive mode.
1.
so oft drücken, bis in der LED-Anzeige die LED 4
für die Intensivstufe 1 leuchtet.
2.
so oft drücken, bis in der LED-Anzeige die LED 5
für die Intensivstufe 2 leuchtet.
a
After approx. 6 minutes, the appliance automatically
switches to fan setting 3.
Switching off intensive mode
▶
To select a fan setting of your choice, press .
a
After approx. 6 minutes, the appliance automatically
switches to fan setting 3.
Switching on the fan run-on
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
The fan run-on removes remaining odours and is used
to dry the odour filter after the cooking process.
▶
Press repeatedly until the fan run-on is switched
on.
a
LED 1 for the fan setting lights up in the LED dis-
play. LED 6 flashes for the fan run-on.
a
The appliance switches off automatically after ap-
prox. 10 minutes.
Switching off the fan run-on
▶
Press .
a
This temporarily stops the fan run-on.
Switch on automatic mode
1
The optimum fan setting is set automatically using a
sensor.
▶
Press .
a
In the LED display, LED 6 lights up for automatic
mode.
Switch off automatic mode
1
▶
Press .
a
The appliance switches to the fan setting that was
previously set.
a
The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a
Automatic mode runs for a maximum of four hours.
Intermittent ventilation
With interval ventilation, the ventilation system switches
on and off in the selected setting for the selected time.
Note:
This function is only available via a mobile device
with the Home Connect app.
If the interval ventilation is switched on, LED 6 continu-
ously flashes in the LED display for the interval ventila-
tion and the LED for the selected fan setting lights up.
As soon as the ventilation time ends, the LED for the
fan setting you have selected goes out. LED 6 contin-
ues to flash.
Sensor control
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes. De-
pending on the setting of the sensor sensitivity, the op-
timum fan setting automatically switched on.
If the sensor control system reacts too weakly or too
strongly, the setting for the sensor sensitivity may
change.
¡
Default setting: Fan setting 3
¡
Lowest setting: Fan setting 1
¡
Highest setting: Fan setting 5
Setting the sensor control
Requirement:
The appliance is switched off.
1.
Press and hold and for approx. three seconds.
2.
Press or to change the setting.
To cancel the setting, press .
3.
To save the setting, press and hold and for ap-
prox. three seconds.
1
Depending on the appliance specifications
Summary of Contents for LR18RPU25
Page 23: ......
