background image

en 

Before using for the first time

6

Tip: 

Align the remote control as precisely as possible

to the infrared receiver for the LED display.

Switch the appliance on or off

Switch on automatic mode

 1

Increase the fan setting

Decrease the fan setting

Switch the lighting on or off

Reduce the brightness

Increase the brightness

Switch the fan run-on on or off

Switch Home Connect on or off

Reset the filter saturation indicator

1

Depending on the appliance specifications

LED display

Die LED-Anzeige zeigt eingestellte Werte und Funk-
tionen.

8

1

2

3

4

5

6

7

1

Fan setting 1/grease filter saturation display

2

Fan setting 2/odour filter saturation indicator

3

Fan setting 3

4

Intensive mode 1

5

Intensive mode 2

6

Automatic mode 

 1

/fan run-on time/interval vent-

ilation

7

Home Connect

8

Infrared receiver

1

Depending on the appliance specifications

Before using for the first time

Configure the settings for initial start-up. Clean the ap-
pliance and accessories.

Setting an operating mode

Your appliance is set to air extraction mode by default.
To use it in circulating-air mode, you must set the oper-
ating mode.

Note: 

For use in circulating-air mode, you require addi-

tional Accessories → 

Page 14

.

Requirement:

 The appliance is switched off.

1.

Press and hold ⁠  and ⁠  for approx. three seconds.

To set circulating-air mode (non-regenerable fil-
ter), press ⁠ /⁠  until LED 2 lights up in the LED
display.

To set circulating-air mode (non-regenerable fil-
ter), press ⁠ /⁠  until LED 3 lights up in the LED
display.

To convert the electronic control back to opera-
tion without the air recirculation filter, press ⁠ /⁠
until LED 1 lights up on the LED display.

2.

To save the setting, press and hold ⁠  and ⁠  for ap-
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
To cancel the setting, press ⁠ .

a

A signal tone sounds as soon as the selected set-
ting is saved.

Basic operation

You can find out everything you need to know about
operating your appliance here.

Switching on the appliance

Requirement:

 Align the remote control as precisely as

possible to the infrared receiver for the LED display.

Press ⁠  to switch on the appliance.

a

The appliance starts at fan setting 2.

a

The LED for the set fan setting lights up in the LED
display.

Switching off the appliance

Switch the appliance off when you are not using it.

Press ⁠  to switch the appliance off.

a

The appliance switches off. Any functions currently
in progress are cancelled.

Selecting a fan setting

Press ⁠  or ⁠ .

a

The LED for the set fan setting lights up in the LED
display.

Summary of Contents for LR26CBS20





























Reviews: