background image

Configuration 

34 

Building Technologies

 

 048_DMS_NK8237_ICC_MP4.40_A6V10316241_a_en.doc

Fire Safety & Security Products 

 

06.2011

 

7.3 

Creating a new NK8237 Composer project 

 

In the Composer environment, new NK8237 projects should be started from an 
empty template. Depending on the DMS8000 installation you have, there are two 
ways to do that. 

  If your DMS8000 installation only includes the 

Composer tool

 (as documented 

in the installation section 6.1.3.1 at p. 25), you can just select the 

New

 com-

mand in the 

Project Management

 window (Fig. 27) to open a new empty pro-

ject and start the NK8237 configuration. 
If Composer is open, you can also click 

File 

 New

 on the menu bar. 

 

Fig. 27  Starting a new project on a Composer-only station 

In this type of scenario, you can skip the remaining part of this section and pro-
ceed directly to section 7.4 below. 

  Instead, starting a new Composer project on a computer where 

MM8000 or 

MK8000 product

 is installed (Stand-alone station setups) results in a predefined 

MM8000 or MK8000 template being used. In this case, a specific procedure is 
required to restore an empty template. You need to operate as described here 
below. 

 

 

 

 

 

Do not use an MM8000 or MK8000 template for configuring the NK8237, 
which cannot be used in MM8000 or MK8000 configurations. In such cases, 
you can apply the NK8232 and NK8235 units. 

 

 

 

Creating a new NK8237 project on an MM8000/MK8000 station 
1. 

In Project Management, select 

Restore

The Restore window displays. 

2. 

In the line corresponding with 

File to be restored

, click 

Browse

The Select restore File window displays. 

3. 

Select the file 

Empty.bak

 in the folder: 

<InstallationDir> \ Sample Projects 

with the default installation folder being: 

C:\Program files\DMS8000

 (assuming 

an English version of Windows). 

4. 

Click 

Open

 (see Fig. 28). 

Summary of Contents for NK8237 MP4.40





































































Reviews: