background image

Maintenance and diagnostics 

55 

Building Technologies

 

 048_DMS_NK8237_ICC_MP4.40_A6V10316241_a_en.doc

Fire Safety & Security Products 

 

06.2011

 

9.2 

SNMP monitoring 

 

The NK823x units can support the SNMP protocol (Simple Network Management 
Protocol) to enable remote stations to monitor the units for conditions that may re-
quire administrative attention. 

Using the SNMPv1 (RFC 1155-1157) on the UDP port 161, the NK823x provides 
two sets of internal information variables using the community IDs listed here be-
low that enable the access to the MIB (Management Information Base) name-
space. 

-  Public, providing a basic set of information 

-  Engineer, providing the access to the complete set of information 

Note that the event-based notifications (trap) is not supported. 

9.3 

The NW8204 maintenance and diagnostic tool 

 

The NW8204 is a powerful maintenance and diagnostic tool. In the event that a 
problem occurs during or after NK82xx configuration, you use the NW8204 main-
tenance tool’s FTP (File Transfer Protocol) and diagnostic interface to locate where 
the problem occurred so you can resolve it. This tool provides functionalities for 
(but not limited to) the following: 

 Downloading 

firmware 

  Setting IP addresses 

  Loading default configurations 

  Using available diagnostic files 

Since the NW8204 maintenance tool is designed mainly for customer support / 
technical use, this guide covers only the most important features used for trouble-
shooting. 

You access the NW8204 tool by installing and then launching the application on 
the host DMS. 

9.3.1 

Launching NW8204 from DMS host 

 

 

 

 

 

 

You need to install the NW8204 maintenance tool (via the installation CD) on the 
host DMS before proceeding, if it is not already installed. 

 

For NW8204 installation instructions, see section 6.3 at p.29. 

To access the NW8204 tool, do the following: 
1. 

Select Start 

 Programs 

 NW8204 

 NW8204 (executable file). 

You are logged in as ‘guest’ (default user type) when the NW8204 window ap-
pears. 

Note:

 To change user type (for example from ‘guest’ to ‘admin’), select 

Change 

User

 to display the Login window. (See information table below.) 

 

 

 

 

 

User types:

 There are two ways you can log in to the NW8204 tool. 

– 

Guest

 user: (Default) User Name = “guest” / Password = “guest” 

(recommended – Read-only privileges); 

– 

Administrative

 user: Call customer support for username and password. 

(Read/Write privileges). 

Note:

 Case sensitive – enter letters in lower case only. 

 

 

 

Summary of Contents for NK8237 MP4.40





































































Reviews: