CE1B3077en / 06.10.2008
Subject to change
Building Technologies
Do you want to set the timers? (RDE410 only)
Do you want to view the timer settings? (RDE410 only)
Do you want to reload the default timer settings? (RDE410 only)
Commissioning
(by qualified HVAC installer)
To adapt the controller to your system and optimize the control performance, a number of
control parameters can be set. This can also be made during operation without opening
the controller.
Recalibrating the temperature sensor
Energy Saving mode
If you want to change the factory-set temperature setpoint (16 °C for heating),
parameter P11 must be adjusted.
Important:
The setpoint of Energy Saving mode can be set to
OFF
. This
means that the controller will be deactivated !
Risk of frost,
i.e. no protective
heating function.
Control parameters
If you want to change the control parameters, proceed as follows:
+ / –
+ / –
+ / –
+ / –
1. Set the controller to Frost Protection mode .
2. Press
+
and
–
simultaneously for a minimum of 3 seconds.
Release the buttons and, within 2 seconds, press
+
again for 3 seconds. The display will show “P01”.
3. Select the required parameter by repeatedly pressing
+
or
–
.
4. Press
+
and
–
simultaneously. The current value of the selected parameter starts to flash. Adjust the
parameter by pressing
+
or
–
.
5. Press
+
and
–
simultaneously again to display the next parameter.
6. If you wish to display and change additional parameters, repeat steps 3 through 5.
7. 10 seconds after the last display or setting, all changes are stored and the controller will leave the parameter
setting mode.
Please write down all changes you make !
(All temperature settings can be made in increments of 0.5 °C)
Energy saving tips without sacrificing comfort
:
•
Never allow room temperatures to exceed 21 °C
•
Set the controller to Energy Saving mode (or Frost Protection mode), even if you are absent for short periods
of time only
•
Air out the rooms briefly, but with windows wide open
A..
+ / –
A..
A..
To set the timers, keep the button depressed for 3 seconds to go to the
timer setting mode (Auto Timer).
This mode is indicated by ”Ax” appearing on the display (x = Auto Timer 1...8)
and the time xx:xx flashing. For each timer, proceed as follows:
1. The
and
icons are displayed. Press
+
or
–
to set the Comfort
mode start time and confirm by pressing .
2. The
and icons are displayed. Press
+
or
–
to set the Comfort
mode end time (or Energy Saving mode start time) and confirm by
pressing .
3. Icon
flashes. Press
+
or
–
to select or deselect each day and
advance to the next day. Confirm setting for the actual timer by pressing
and advance to the next timer.
The controller leaves the timer setting mode automatically after 20 seconds
when no button is pressed. All changes made after the last press of will
not be saved !
Press the
button to sequentially review all 8 Auto Timers.
+
/
– /
1.
Set the controller to Frost Protection mode .
2.
Press
+
and
–
simultaneously for 3 seconds. Release the buttons
and, within 2 seconds, press twice the
button.
Day/s
Time of day when controller is in Comfort mode
Mo (1) –
Fr (5)
06:30 – 08:30 (A1)
17:30 – 22:30 (A2)
Sa (6)
08:00 – 23:00 (A3)
Su (7)
08:00 – 22:30 (A4)
Default
settings
- In the remaining time, the RDE410 is in Energy Saving mode
- Timers A5…A8 have no default settings
If the room temperature displayed by the controller does not accord with the
temperature effectively measured, the temperature sensor can be
recalibrated. Using parameter P05, the temperature can be adjusted by
pressing
+
or
–
in steps of 0.5 °C. The maximum recalibration range is
+/- 3 °C.
Para-
meter
Controller’s factory-set parameters:
Setting range
P02 Mode selection by operating mode button
1 = Frost Protection –
Comfort
mode
1 = Frost Protection –
Comfort
mode
2 = Frost Protection –
Comfort –
Energy Saving mode
P04 Selection of °C or °F
°C
°C or °F
P05 Temperature sensor calibration
0.0 °C
– 3 … 3 °C
P06 Standard temperature display
0 = room temperature
0 = room temperature
1 = setpoint
P08 Comfort basic setpoint
20 °C
5 ... 40 °C
P09 Min. setpoint limitation in Comfort mode (Wmin
Comf
)
5 °C
5 ... 40 °C
P10 Max. setpoint limitation in Comfort mode (Wmax
Comf
)
35 °C
5 ... 40 °C
P11 Heating setpoint in Energy Saving mode
16 °C
OFF, 5…18 °C
P14
Button lock
(Press the operating mode button for 7 seconds to
lock or unlock the buttons)
0 = disabled
0 = disabled
1 = auto lock
2 = manual lock
