background image

N3057en 
2014-10-28 

Building Technologies

 

 

 

        

 

3

057

 

 

                     

 

 

 

 

RDF110

 

RDF110.2 

RDF110/IR 

RDF110.2/IR 

 

 

 

Room Temperature  

Controllers with LCD 

RDF110… 

 

for 2-pipe fan coil units 
for compressors in DX type equipment 
 

 

Output for on / off valve actuator or 1-stage compressor 

3-speed fan control: Automatic or manual 

Adjustable commissioning and control parameters 

Optional display of room temperature or setpoint 

Minimum and maximum setpoint limitation 

Operating

 

voltage AC 230 V 

 

Additional features of RDF110 

Automatic heating / cooling changeover 

Operating modes: Normal operation, Economy (Energy saving) and Protection 

(Standby) 

Input for heating / cooling changeover or return air temperature sensor 

Potential-free input for operating mode changeover (key card contact, etc.) 

Function for avoiding damage resulting from moisture 

 

Additional features of RDF110.2

 

Manual heating / cooling changeover 

Operating modes: Normal operation, Protection (Standby) 

 

Optional 

Infrared remote control (RDF110/IR, RDF110.2/IR) 

Summary of Contents for RDF110















Reviews: