CE1B3176.3en / 2012-08-29
Subject to change
Siemens Building Technologies
Button lock
Press operating mode button for 3 seconds to lock or unlock the buttons if
manual button lock is configured (parameter P14 = 2).
The thermostat automatically locks the buttons 30 seconds after the last
adjustment if "Auto lock" is configured (P14 = 1).
The key symbol
indicates locked buttons.
Reminder to clean filters
External faults
Commissioning
(by qualified HVAC installer)
To adapt the thermostat to your system and optimize the control performance, a number
of control parameters can be adjusted. This can also be made during operation without
opening the thermostat.
Control sequence
Recalibrating the sensor
Note: Economy mode
The Economy setpoints are factory-set to 15 °C for heating and 30 °C for
cooling. Use parameters P11 and P12 to adjust the values.
Important
:
You can set these setpoints to
OFF
; the thermostat then is
inactive,
i.e. no protective heating or cooling function.
Risk of frost!
Control parameters
Proceed as follows to change the most important control parameters:
(Your HVAC installer can set additional parameters)
+ / -
+ / -
+ / -
+ / -
1.
Set the thermostat to Protection
2.
Press
-
and
+
simultaneously for a minimum of 4 seconds.
Release them and, within 2 seconds, press
+
again until "P01" is displayed.
3.
Repeatedly press the
+
or
–
button to select the required parameter.
P01
P02
P08
P13
+
-
+
-
-
+
3057z03
P14
-
+
-
P12
+
-
4.
Press
+
and
–
simultaneously, the current value of the selected parameter starts to flash, allowing you to change
the value by repeatedly pressing
+
or
–
.
5.
The next parameter is displayed when you press
+
and
–
again simultaneously.
6.
Repeat steps 3 to 5 to display and change additional parameters.
7.
15 seconds after the last display or setting, all changes are saved and the thermostat will leave parameter entry
mode.
Para-
meter
Description
Factory setting
Setting range
P01 Control
sequence
2-pipe
: [0…3]
1 (Cooling only)
4-pipe:
[2…4]
4 (Heating & Cooling)
0 = Heating only
1 = Cooling only
2 = Manual H or C
3 = Auto Changeover
4 = Heating & cooling
P02
Mode selection by user via operating mode button
1 (Protection,
Comfort)
1 = Protection, Comfort,
2 = Protection, Comfort,
Economy
P04
Selection of °C or °F
0 (°C)
0 = °C
1 = °F
P05 Sensor
calibration
0.0 K
– 3 ... +3 K
P06
Standard temperature display
0 (Room temp.)
0 = Room temperature
1 = Setpoint
P07
Additional user information
0 (no display)
0 = no display
1 = Temp in °C / °F
P08
Comfort basic setpoint
21 °C
5 ... 40 °C
P09
Minimum setpoint limitation in Comfort
(Wmin
Comf
) 5 °C
5 ... 40 °C
P10
Maximum setpoint limitation in Comfort
(Wmax
Comf
) 35 °C
5 ... 40 °C
P11
Setpoint of heating in Economy mode
(Wheat
Eco
) 15 °C
OFF, 5 °C…Wcool
Eco
P12
Setpoint of cooling in Economy mode
(Wcool
Eco
) 30 °C
OFF, Wheat
Eco
…40°C
P13
Electric heater in cooling mode
ON
OFF = Disabled
ON = Enabled
P14
Button lock
(Press operating mode button for 3 seconds to lock or
unlock the buttons)
0 (Disabled)
0 = Disabled
1 = Auto lock
2 = Manual lock
The control parameters displayed depend on the DIP switch settings made
Please record all changes you make!
(All temperature settings can be made in increments of 0.5 K)
FIL
This message reminds you to clean the filter on your HVAC equipment.
It will appear after
__________ "fan operating hours" and disappear when
the thermostat is set to Protection ( ).
This reminder must be configured by your HVAC installer.
AL1
AL2
This alarm message tells you an external alarm has occurred:
AL1 :
______________________
AL2 :
______________________
The alarms are configured by your HVAC installer
The thermostat can be used in systems either for
heating only
or
cooling
only
,
manually selection of heating or cooling
, or
automatic heating / cooling
changeover
. Depending on the selected application, the relevant modes are
available and can be adjusted by commissioning parameter P01 if needed.
The factory setting for 2-pipe application is "C
ooling only"
, and for 4 pipe
application "Heating and Cooling"
If the room temperature displayed by the thermostat does not agree with the
temperature effectively measured (after min 1 hour of operation), the tem-
perature sensor can be recalibrated. With parameter P05 the temperature can
be adjusted by + or – 0.5 °C up to a maximum of + / - 3 °C.
