Operating instructions
Landis & Staefa REV15…
REV15… - the temperature controller that allows you to set the ideal room temperature at the time you want. There
are several switching patterns available that can be set to suit your specific needs. You can either rely on the
factory settings or make settings taillored to your personal needs.
Auto
Run
°C
Day
A1
A2
A3
A4
A5
A6
Setting slider
Changing the
setting values
Operation
Weekly mode with
3 heating periods (A 1-5) /
1 heating period (B 6-7)
Continuous
normal temperature
Continuous
economy temperature
Standby
with frost protection
Operating mode
selector
Change
between normal and
economy mode up to the
next switching point
Warmer/colder setting
valid up to the next
switching point
(increments of 0.2 ºC,
± 4 ºC max.)
Switching pattern
with time cursor
Display
24-hour mode A
with 3 heating periods
24-hour mode B
with 1 heating period
Settings
Normal temperature
Economy temperature
Holiday period
Weekday (1=Monday / 7=Sunday)
Room temperature (measured)
Time of day
Remote operation active
(if connected)
Standby
Normal temperature
Heating on
Economy temperature
Holiday mode
Replace batteries
Auto A/B
1.5V 'AA'
1.5V 'AA'
Time
Operating mode
Auto
Run
1
2
3
4
5
6
7
0
6
12
18
24
A
B
B1
B2
Day
Weekday
Switching times A1... A6
A1
A2
A3
A4
A5
A6
B1
B2
Switching times B1... B2
A
B
Current 24-hour mode
A
B
2225Z11E
Commissioning with quick startup
The controller is supplied with factory-set switching patterns, switching times and temperatures. To commission it,
proceed as follows:
1.5V 'AA'
1.5V 'AA'
Remove the black transit tabs from the two batteries. Check to see if the battery holder is in its correct
position. The controller switches itself on.
Move the setting slider to this position. Press buttons
to set the correct time of day.
Day
Move the setting slider to this position. Press buttons
to set the correct weekday.
(1 = Monday…7 = Sunday).
Auto
Run
Move the setting slider back to position on the right, because only that position allows you to close the
cover.
Select the required operating mode with the operating mode selector.
Fold up operating instructions again, place them back into the cover and close the cover again.
Do you want to use automatic operation?
If that is the case, set the operating mode
selector to one of the following positions:
Auto A/B
You use the weekly setting with automatic
changeover from three heating periods on
weekdays (A 1-5) to one heating period on
weekends (B 6-7).
A
You use the 24-hour setting A with three
heating periods.
B
You use the 24-hour setting B with one
heating period.
The display shows the respective letter A or B.
Do you require continuous normal
temperature?
Move the operating mode selector to «Normal
temperature». This ensures continuous
heating to the normal temperature. The
display shows
.
Do you require continuous economy
temperature?
Move the operating mode selector to
«Economy temperature». This ensures
continuous heating to the economy
temperature. The display shows
.
Do you require continuous standby with frost
protection?
Move the operating mode selector to
«Standby». In that case, heating is provided
only when the room temperature falls below
the preset frost protection limit (5 °C). The
display shows
.
Do you feel too warm or too cold?
°C
By pressing these buttons, you increase or
decrease the actual room temperature in
increments of 0.2 °C by a maximum of
±
4°C.
The display first shows the newly selected
temperature and then the actual value again.
These changes are valid only up to the
next switching point.
If, as a result of the
factory settings, you always feel either too
warm or too cold, you should readjust the
temperature
or
to suit your needs.
