Siemens SENTRON 3VA1 Manual Download

Page: 81 / 676

Description

2.6 Protection system

3VA molded case circuit breakers with IEC certificate
Manual, 03/2019, A5E03603177010-03

2.6.8

Neutral conductor protection (N)

The ID letter for neutral conductor protection is "N".
The neutral conductor protection system protects the neutral conductor against overloads

and short circuits.
The letters I

refer to the current setting value; the associated setting time is identical to t

Note
A neutral conductor with full cross sectional area (distributed neutral conductor of the same

size as the phases) is normally protected by the phase protection system and does not

require separate protection.

Neutral conductor protection

Neutral conductor protection must be implemented in accordance with the standards valid in

the country of installation. Possible reasons for implementing neutral conductor overload

protection are:

●

The neutral conductor has a smaller cross section than the phase conductors.

●

Harmonic levels in the installation are expected to be higher than normal.

●

A large number of loads, or predominantly single-phase loads, will be connected.

Neutral conductor protection and 3VA1 molded case circuit breakers
The following 3VA1 molded case circuit breakers have neutral conductor protection:

●

All 4-pole versions of 3VA11, 3VA12, 3VA13, 3VA14 (TM210, TM220, TM240)

All of these molded case circuit breakers are available in versions without or with

100% neutral conductor protection. A version with 50% neutral conductor protection is

available in addition for rated operational currents greater than 100 A.

Summary of Contents for SENTRON 3VA1





































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SENTRON 3VA1

Reviews:

Related manuals for SENTRON 3VA1

Brands by name

Popular brands

Siemens SENTRON 3VA1, Manual

Search results

Summary of Contents for SENTRON 3VA1

Reviews:

Related manuals for SENTRON 3VA1

Brands by name

Popular brands