background image

 

CP 343-1 
Manual, 12/2018, 

C79000−G8976−C201

-08 

65

 

 

Technical specifications 

 

 

Table 8- 1 

Technical specifications 

Technical specifications 
Attachment to Industrial Ethernet 
Number 

1 x PROFINET interface with 2port switch 

Execution 

Connector 

2 x RJ-45 jacks 

Transmission rate 

10 / 100 Mbps 
When working with PROFINET IO and 

cyclic transfer, the transmission speed of 

100 Mbps full duplex is mandatory. 

Aging time 

5 minutes 

Special features of the X1P1R and 

X1P2R ports 

Integration in ring topology / MRP possible 

Electrical data 
Supply voltage 

External power supply 
Permitted range 

24 VDC 
+20.4 V to +28.8 V 

From backplane bus 

5 VDC 

Current consumption 

From external power supply 

200 mA maximum 

From backplane bus 

200 mA maximum 

Effective power loss 

5.8 W 

Permitted ambient conditions 
Ambient temperature 

During operation with the rack in-

stalled horizontally 

0 ℃ to +60 ℃

 

During operation with the rack in-

stalled vertically 

0 ℃ to +40 ℃

 

During storage 

-

40 ℃ to +70 ℃

 

During transportation 

-

40 ℃

 

to +70 ℃

 

Relative humidity 

During operation 

≤ 95 % at 25 °C, no condensation

 

Operating altitude 

During operation 

 2,000 m above sea level 

Contaminant concentration 

Acc. to ISA-

S71.04 severity level G1, G2, G3

 

Design, dimensions and weight 
Module format 

Compact module for S7-300, single width 

Degree of protection 

IP20 

Weight 

Approx. 220 g 

Dimensions (W x H x D) 

40 x 125 x 120 mm 

Installation options 

Mounting in an S7-300 rack 

Product functions * 

* You will find the product functions in the sectio

Properties / services (Page 11). 

Summary of Contents for SIMATIC NET CP 343-1















































































Reviews: