background image

 

 

Safety Guidelines 

Safety Guidelines 

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent 

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert 

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are 

graded according to the degree of danger. 

DANGER 

 

indicates that death or severe personal injury will result if proper precautions are not taken. 

WARNING 

 

indicates that death or severe personal injury may result if proper precautions are not taken. 

CAUTION 

 

with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken. 

CAUTION 

 

without a safety alert symbol, indicates that property damage can result if proper precautions are not taken. 

NOTICE 

 

indicates that an unintended result or situation can occur if the corresponding information is not taken into 

account. 

If more than one degree of danger is present, the warning notice representing the highest degree of danger will 

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to 

property damage. 

Qualified Personnel 

The device/system may only be set up and used in conjunction with this documentation. Commissioning and 

operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes 

in this documentation qualified persons are defined as persons who are authorized to commission, ground and 

label devices, systems and circuits in accordance with established safety practices and standards. 

Prescribed Usage 

Note the following: 

WARNING 

 

This device may only be used for the applications described in the catalog or the technical description and only 

in connection with devices or components from other manufacturers which have been approved or 

recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage, 

positioning and assembly as well as careful operation and maintenance. 

Trademarks 

All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this 

publication may be trademarks whose use by third parties for their own purposes could violate the rights of the 

owner. 

Disclaimer of Liability 

We have reviewed the contents of this publication to ensure consistency with the hardware and software 

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the 

information in this publication is reviewed regularly and any necessary corrections are included in subsequent 

editions. 

 

 

Siemens AG 
Automation and Drives 
Postfach 48 48 
90327 NÜRNBERG 
GERMANY 

A5E02135173-01 
Ⓟ 04/2008 

Copyright © Siemens AG 2008. 
Technical data subject to change

 

기기는

 

업무용

(A

전자파

 

적합기기로서

 

판매자

 

또는

 

사용자는

 

 

점을

 

주의하시기

 

바라며

 

가정

 

외의

 

지역에서

 

사용하는

 

것을

 

목적으로

 

합니다

.

Summary of Contents for SIMATIC PC 577B





























Reviews: