background image

Further information

You can find more detailed information about the EGB Guideline in Annex B in the section with 

the same name.

1.2.2

Notes on use

WARNING

Hazards on an unprotected machine or plant
According to the results of a risk analysis, hazards can occur on an unprotected machine. 

The hazards can result in personal injury.
According to the risk analysis, the risk of personal injury can be avoided with the following 

measures:
● Additional protective devices on the machine or plant. With this, especially the 

programming, configuration and wiring of the inserted I/O modules have to be executed, 

in accordance with the necessary risk analysis identified safety performance (SIL, PL or 

Cat.).

● The correct use of the device has to be verified with a function test on the system. This 

test can detect programming, configuration and wiring errors.

● Documentation of the test results that you can enter in the relevant safety records when 

required.

NOTICE
Ambient conditions
Ambient conditions for which the device is not suitable can cause faults or damage the device.
Note the following:
● Operate the device only in closed rooms. Failure to comply nullifies the warranty. 
● Operate the device only in accordance with the ambient conditions specified in the 

technical specifications.

● Protect the device against dust, moisture and heat.
● Do not expose the device to direct sunlight or other strong sources of light.
● Without additional measures, such as a supply of clean air, the device may not be used 

in locations with harsh operating conditions caused by acidic vapors or gases.

● Observe the permissible mounting positions of the device.
● Do not obstruct the venting slots of the device.

Note
Use in an industrial environment without additional protective measures
This device was designed for use in a normal industrial environment according to 

IEC 60721-3-3.

Safety instructions

1.2 Specific safety instructions for the SIMOTION P320-4

SIMOTION P320-4 E / P320-4 S

Manual, 03/2018, A5E36004933B

19

Summary of Contents for SIMOTION P320-4 E







































































































































































Reviews: