background image

Preface

Preface

This document is part of the SIMOTION P documentation package.
This documentation describes the SIMOTION P320‑4 hardware platform which can be 

delivered in the SIMOTION P320-4 E and SIMOTION P320-4 S hardware versions:
● SIMOTION P320‑4 E with the Windows Embedded Standard 7 32-bit operating system and 

real-time expansion for SIMOTION.

Successor to SIMOTION P320-3.

● SIMOTION P320‑4 E with the Windows 7 Ultimate 32-bit operating system and real-time 

expansion for SIMOTION.

Successor to SIMOTION P350-3.

References

The following documents contain the descriptions for the SIMOTION P hardware platform:
● SIMOTION P320-4 E / P320-4 S, Manual, Edition 09/2016
● SIMOTION P320-4 E / P320-4 S, Commissioning and Hardware Installation Manual, Edition 

09/2016

Validity range

This manual applies to the SIMOTION P320-4 E and SIMOTION P320-4 S devices as of 

product level SIMOTION V4.5.

Standards

The SIMOTION system was developed in accordance with ISO 9001 quality guidelines.

Chapters in this documentation

The following sections describe the purpose and the use of this documentation:
● Safety instructions

Contains fundamental safety instructions for SIMOTION and specific safety instructions for 

SIMOTION P320-4.

● Description

System overview and product description for SIMOTION P320-4. The communication 

versions are also described.

● Use planning

Points to note in advance: upon delivery, the permitted installation positions, environmental 

and ambient conditions and electromagnetic compatibility.

SIMOTION P320-4 E / P320-4 S

Manual, 03/2018, A5E36004933B

3

Summary of Contents for SIMOTION P320-4 E







































































































































































Reviews: