2 Parameters
2.2 List of parameters
SINAMICS DCM
80
List Manual (LH8), 02/2015, 6RX1800-0ED76
Dependency:
Refer to: p0404
Note:
ZM: Zero mark
This parameter is only used for diagnostics.
A value of zero is displayed if an encoder is not present.
Re bit 20, 21 (voltage level 5 V, voltage level 24 V):
The voltage level cannot be detected. Therefore, these bits are always set to 0.
Description:
Displays the encoder configuration supported by the Sensor Module.
Index:
[0] = Encoder 1
[1] = Encoder 2
[2] = -
Dependency:
Refer to: p0404
Note:
ZM: Zero mark
This parameter is only used for diagnostics.
A value of zero is displayed if an encoder is not present.
Description:
Sets the Sensor Module configuration.
17
Track A/B analog
Yes
No
-
20
Voltage level 5 V
Yes
No
-
21
Voltage level 24 V
Yes
No
-
22
Remote sense (only SMC30)
Yes
No
-
23
Resolver excit
Yes
No
-
r0456[0...2]
Encoder configuration supported / Enc_config supp
DC_CTRL,
DC_CTRL_R,
DC_CTRL_R_S,
DC_CTRL_S
Can be changed:
-
Calculated:
-
Access level:
3
Data type:
Unsigned32
Dyn. index:
-
Func. diagram:
-
P-Group:
Encoder
Unit group:
-
Unit selection:
-
Not for motor type:
-
Scaling:
-
Expert list:
1
Min Max
Factory
setting
- -
-
Bit field:
Bit
Signal name
1 signal
0 signal
FP
00
Linear encoder
Yes
No
-
01
Absolute encoder
Yes
No
-
02
Multiturn encoder
Yes
No
-
03
Track A/B sq-wave
Yes
No
-
04
Track A/B sine
Yes
No
-
05
Track C/D
Yes
No
-
06
Hall sensor
Yes
No
-
08
EnDat encoder
Yes
No
-
09
SSI encoder
Yes
No
-
10
DRIVE-CLiQ encoder
Yes
No
-
11
Digital encoder
Yes
No
-
12
Equidistant zero mark
Yes
No
-
13
Irregular zero mark
Yes
No
-
14
Distance-coded zero mark
Yes
No
-
15
Commutation with zero mark (not ASM)
Yes
No
-
16
Acceleration
Yes
No
-
17
Track A/B analog
Yes
No
-
20
Voltage level 5 V
Yes
No
-
21
Voltage level 24 V
Yes
No
-
22
Remote sense (only SMC30)
Yes
No
-
23
Resolver excit
Yes
No
-
r0458[0...2]
Sensor Module properties / SM properties
DC_CTRL,
DC_CTRL_R,
DC_CTRL_R_S,
DC_CTRL_S
Can be changed:
-
Calculated:
-
Access level:
3
Data type:
Unsigned32
Dyn. index:
-
Func. diagram:
4704
P-Group:
Encoder
Unit group:
-
Unit selection:
-
Not for motor type:
-
Scaling:
-
Expert list:
1
Min Max
Factory
setting
- -
-
Summary of Contents for SINAMICS DCM
