manualshive.com logo in svg

Siemens SINAMICS S150, Operating Instructions Manual

The Siemens SINAMICS S150, a powerful drive system, revolutionizes industrial automation. With its excellent performance and advanced features, this product guarantees seamless operations. Enhance your experience with the Operating Instructions Manual, available for free download from our website, empowering you to unleash the full potential of this exceptional device.

Share
Download
background image

 

Table of contents 

  

Drive converter cabinet units 
Operating Instructions, 07/07, A5E00288214A 

11

 

9 

Functions, monitoring, and protective functions..................................................................................... 301 
9.1 

Chapter content .........................................................................................................................301 

9.2 

Active Infeed functions...............................................................................................................303 

9.2.1 

Line and DC link identification....................................................................................................303 

9.2.2 

Harmonics controller ..................................................................................................................304 

9.2.3 

Variable power factor (reactive power compensation) ..............................................................305 

9.2.4 

Settings for the infeed (Active Infeed) under difficult line conditions .........................................306 

9.3 

Drive functions ...........................................................................................................................308 

9.3.1 

Motor identification and automatic speed controller optimization..............................................308 

9.3.1.1  Standstill measurement .............................................................................................................309 

9.3.1.2  Rotating measurement and speed controller optimization ........................................................311 

9.3.2 

Efficiency optimization ...............................................................................................................314 

9.3.3 

Vdc control .................................................................................................................................315 

9.3.4 

Automatic restart function ..........................................................................................................318 

9.3.5 

Flying restart ..............................................................................................................................321 

9.3.5.1  Flying restart without encoder....................................................................................................322 

9.3.5.2  Flying restart with encoder.........................................................................................................323 

9.3.5.3  Parameters.................................................................................................................................323 

9.3.6 

Motor changeover/selection.......................................................................................................324 

9.3.6.1  Description .................................................................................................................................324 

9.3.6.2  Example of changing over between two motors........................................................................324 

9.3.6.3  Function diagram .......................................................................................................................325 

9.3.6.4  Parameters.................................................................................................................................326 

9.3.7 

Friction characteristic curve .......................................................................................................326 

9.3.8 

Increasing the output frequency.................................................................................................328 

9.3.8.1  Increasing the pulse frequency..................................................................................................329 

9.3.8.2  Parameters.................................................................................................................................330 

9.3.9 

Runtime (operating hours counter) ............................................................................................331 

9.3.10  Simulation operation ..................................................................................................................332 

9.3.11  Direction reversal .......................................................................................................................333 

9.3.12  Unit changeover.........................................................................................................................334 

9.3.13  Derating behavior at increased pulse frequency .......................................................................336 
9.4 

Extended functions ....................................................................................................................338 

9.4.1 

Technology controller.................................................................................................................338 

9.4.2 

Bypass function..........................................................................................................................341 

9.4.2.1  Bypass with synchronizer with degree of overlapping (p1260 = 1) ...........................................342 

9.4.2.2  Bypass with synchronizer without degree of overlapping (p1260 = 2) ......................................344 

9.4.2.3  Bypass without synchronizer (p1260 = 3)..................................................................................346 

9.4.2.4  Function diagram .......................................................................................................................347 

9.4.2.5  Parameters.................................................................................................................................348 

9.4.3 

Extended braking control ...........................................................................................................349 

9.4.4 

Extended monitoring functions...................................................................................................351 

9.4.5 

Closed-loop position control.......................................................................................................353 

9.4.5.1  Actual position value preparation...............................................................................................354 

9.4.5.2  Closed-loop position controller...................................................................................................359 

9.4.5.3  Monitoring functions...................................................................................................................360 

9.4.5.4  Measurement probe evaluation and reference mark search .....................................................362 

9.4.6 

Basic positioner..........................................................................................................................364 

9.4.6.1  Mechanical system ....................................................................................................................366 

9.4.6.2  Limitations..................................................................................................................................368 

9.4.6.3  Referencing................................................................................................................................373 

9.4.6.4  Basic positioner with position tracking .......................................................................................381 

9.4.6.5  Traversing blocks.......................................................................................................................384 

Summary of Contents for SINAMICS S150









































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINAMICS S150

Eaton PowerXL DM1 Series Applications Manual preview
PowerXL DM1 Series
Brand: Eaton Pages: 258
YASKAWA Varispeed G7 Modbus Communication Manual preview
Varispeed G7
Brand: YASKAWA Pages: 92
YASKAWA GA500 series Technical Manual preview
GA500 series
Brand: YASKAWA Pages: 10
Nidec AD07-E-1-1-023-1-0002 Installation & Operating Instructions Manual preview
AD07-E-1-1-023-1-0002
Brand: Nidec Pages: 56
Magnetek GPD 315 Technical Manual preview
GPD 315
Brand: Magnetek Pages: 119
Fuji Electric FRENIC-Lift LM2A Series Instruction Manual preview
FRENIC-Lift LM2A Series
Brand: Fuji Electric Pages: 73
Piezoconcept TT2 Installation And Operation Manual preview
TT2
Brand: Piezoconcept Pages: 7
KB Electronics 8821 Installation And Operating Instructions Manual preview
8821
Brand: KB Electronics Pages: 20
ElectroCraft CompletePower Plus CPP-A06V48A-SA-CAN User Manual preview
CompletePower Plus CPP-A06V48A-SA-CAN
Brand: ElectroCraft Pages: 48
V&T TS-I Series User Manual preview
TS-I Series
Brand: V&T Pages: 79
Fagor QC-PDS Hardware Manual preview
QC-PDS
Brand: Fagor Pages: 420
IBM 22P9218 User Manual preview
22P9218
Brand: IBM Pages: 74
Balluff BTL5-H1 M Series Condensed Manual preview
BTL5-H1 M Series
Brand: Balluff Pages: 16
ZIEHL-ABEGG ZETADYN 3C Original Operating Instructions preview
ZETADYN 3C
Brand: ZIEHL-ABEGG Pages: 204
ZLTECH ZLAC8015D Quick Start Manual preview
ZLAC8015D
Brand: ZLTECH Pages: 9
Teac CD-540E Installation Manual preview
CD-540E
Brand: Teac Pages: 12
VEM W52R 355 Series Manual preview
W52R 355 Series
Brand: VEM Pages: 25
YASKAWA GPD 315/V7 Technical Manual preview
GPD 315/V7
Brand: YASKAWA Pages: 44

Brands by name

Popular brands

Load more brands