manualshive.com logo in svg

Siemens SINUMERIK 808D, Diagnostic Manual

The Siemens SINUMERIK 808D is an advanced CNC control system that offers precision and efficiency in machining. With its comprehensive Programming and Operating Manual, users can easily navigate and maximize the system's functionalities. Download the manual for free at 88.208.23.73:8080 and unlock the full potential of this groundbreaking product.

Share
Download
background image

Explanation:

The maximum permissible frequency of the currently active encoder (axis-specific interface signal DB380x DBX1.5 / 1.6 

(position measuring system 1/2)) in the axis-specific MD36300 $MA_ENC_FREQ_LIMIT [n] (n ... encoder number, 1 or 2) 

has been exceeded. The reference of the actual value to the mechanical slide position may have been lost.
The alarm can be reprogrammed in MD11412 $MN_ALARM_REACTION_CHAN_NOREADY (channel not ready).
The maximum permissible frequency of the active encoder (axis-specific interface signal V390x0000.2) in axis-specific 

MD36300 $MA_ENC_FREQ_LIMIT [n] (n ... encoder number, 1 or 2) has been exceeded. The reference of the actual 

value to the mechanical slide position may have been lost.
The alarm can be reprogrammed in MD11412 $MN_ALARM_REACTION_CHAN_NOREADY (channel not ready).

Reaction:

Mode group not ready.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Channel not ready.

Remedy:

Check MD36300 $MA_ENC_FREQ_LIMIT [n] and NC/PLC interface signal DB380x DBX1.5 / 1.6 (position measuring 

system 1/2).

Programm 

continuation:

Restart part program.    Clear alarm with the RESET key in all channels of this mode group. Restart part program.

21611

[Channel %1: ] NC-controlled Extended Stop/Retract triggered

Parameters:

%1 = Channel number

Explanation:

"NC-controlled Extended Stop/Retract" triggered.

Reaction:

The NC switches to follow-up mode.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
All channel-specific alarm reactions are delayed with this alarm, alarm display.

Remedy:

Reset

Programm 

continuation:

Clear alarm with the RESET key. Restart part program

21612

[Channel %1: ] Axis %2: enable reset, cause %3

Parameters:

%1 = Channel number
%2 = Axis name, spindle number
%3 = Cause of the alarm

Explanation:

Causes of alarm:
  0: The cause of the alarm cannot be precisely determined.
  1: The interface signal DB380x DBX2.1 (Servo enable) is missing
  2: The interface signal DB380x DBX4001.7 (Pulse enable) is missing
  3: Drive signal DB390x DBX4001.7 (Impulses enabled) is not set
  4: Drive signal DB390x DBX4001.5 (Drive ready) is not set
  5: Drive signal DB390x DBX4000.4 (Autonomous drive) does not follow the NC setpoints
One of the motion-enabling signals (e.g. "Servo enable", "Pulse enable", parking/encoder selection (only for axes) or drive-

specific enables has been reset for the displayed axis. The alarm can be reported with positioning axes, spindles and for 

axes from the geometry grouping.
The axes entered in the channel-specific MD array MD20050 $MC_AXCONF_GEOAX_ASSIGN_TAB are regarded as 

axes belonging to the geometry grouping. Servo enable must exist for all available geometry axes, regardless of whether 

or not they are currently in motion.
Occurs in connection with SAFETY function: If a test stop is performed with linked axes, the alarm is issued if a motion 

command from the ELG grouping is pending during the test stop of the following axis.

SINUMERIK 808D ADVANCED alarms
5.2 NCK alarms

Diagnostics Manual

318

Diagnostics Manual, 06/2015, 6FC5398-6DP10-0BA2

Summary of Contents for SINUMERIK 808D























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 808D

Aegis SPP-HDMI-1201 User Manual preview
SPP-HDMI-1201
Brand: Aegis Pages: 4
Hirose GT16GM Series Instruction Manual preview
GT16GM Series
Brand: Hirose Pages: 6
ADC TrueNet 25-Pair Category 5e Riser Cable Specification Sheet preview
TrueNet 25-Pair Category 5e Riser Cable
Brand: ADC Pages: 4
LEGRAND EZ-RJ AC3450-50 Installation Instructions preview
EZ-RJ AC3450-50
Brand: LEGRAND Pages: 2
Kramer CLS-AOCH/xl Installation Instructions preview
CLS-AOCH/xl
Brand: Kramer Pages: 4
NCR R6 Checkpoint 7360-K093 Kit Instructions preview
R6 Checkpoint 7360-K093
Brand: NCR Pages: 8
Techly A/V Series User Manual preview
A/V Series
Brand: Techly Pages: 12
Hubbell 50 AMP TWIST-LOCK Installation Instructions preview
50 AMP TWIST-LOCK
Brand: Hubbell Pages: 2
Gefen GTV-HDMI1.3-144 User Manual preview
GTV-HDMI1.3-144
Brand: Gefen Pages: 10
Clas Ohlson LCH1312.68-3P Quick Start Manual preview
LCH1312.68-3P
Brand: Clas Ohlson Pages: 2
Rutenbeck POF/UAE 1xUp 0 Installation Instructions preview
POF/UAE 1xUp 0
Brand: Rutenbeck Pages: 4
Votronic USB Charger Panel S Installation And Operating Manual preview
USB Charger Panel S
Brand: Votronic Pages: 2
Lindy 42780 User Manual preview
42780
Brand: Lindy Pages: 12
General Pump DHRWM50200 Quick Start Manual preview
DHRWM50200
Brand: General Pump Pages: 2
DirekTronik 25-0081 Operating Instructions preview
25-0081
Brand: DirekTronik Pages: 4
IKEA FORNIMMA Manual preview
FORNIMMA
Brand: IKEA Pages: 12
Kyocera 14 5046 829 Series Instruction Manual preview
14 5046 829 Series
Brand: Kyocera Pages: 10
nedis VMAT3464AT Quick Start Manual preview
VMAT3464AT
Brand: nedis Pages: 24

Brands by name

Popular brands

Load more brands