manualshive.com logo in svg

Siemens SINUMERIK 808D, Diagnostic Manual

The Siemens SINUMERIK 808D is an advanced CNC control system that offers precision and efficiency in machining. With its comprehensive Programming and Operating Manual, users can easily navigate and maximize the system's functionalities. Download the manual for free at 88.208.23.73:8080 and unlock the full potential of this groundbreaking product.

Share
Download
background image

Programm 

continuation:

Restart part program.    Clear alarm with the RESET key in all channels of this mode group. Restart part program.

25050

Axis %1 contour monitoring

Parameters:

%1 = Axis name, spindle number

Explanation:

The NCK calculates for each interpolation point (setpoint) of an axis the actual value that should result based on an internal 

model. If this calculated actual value and the true machine actual value differ by a larger amount than given in the MD36400 

$MA_CONTOUR_TOL, then the program is canceled and the alarm message is issued.
The alarm can be reprogrammed in the MD11412 $MN_ALARM_REACTION_CHAN_NOREADY (channel not ready).

Reaction:

Mode group not ready.
The NC switches to follow-up mode.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Channel not ready.

Remedy:

Please inform the authorized personnel/service department.
- Check whether the tolerance value set in MD36400 $MA_CONTOUR_TOL is too small.
- Check optimization of the position controller (Kv factor in the MD32200 $MA_POSCTRL_GAIN) to establish whether the 

axis follows the given setpoint without overshooting. Otherwise, the speed controller optimization must be improved or the 

Kv servo gain factor must be reduced.
- Improvement of speed controller optimization
- Check the mechanics (smooth running, inertial masses).

Programm 

continuation:

Restart part program.    Clear alarm with the RESET key in all channels of this mode group. Restart part program.

25060

Axis %1 speed setpoint limitation

Parameters:

%1 = Axis name, spindle number

Explanation:

The speed setpoint has exceeded its upper limit for a longer period than allowed.
The maximum speed setpoint is limited to a certain percentage by the axis-specific MD36210 $MA_CTRLOUT_LIMIT. The 

input value of 100% corresponds to the rated speed of the motor and hence the rapid traverse velocity (exemplary default 

value: 840D=110%).
For SINAMICS: Drive parameter p1082 also has a limiting effect.
If the values are exceeded for a short time, then this is tolerated provided they do not last longer than allowed for in the 

axis-specific MD36220 $MA_CTRLOUT_LIMIT_TIME. The setpoint is limited during this time to the maximum value that 

has been set in (MD36210 $MA_CTRLOUT_LIMIT).
The alarm can be reprogrammed in the MD11412 $MN_ALARM_REACTION_CHAN_NOREADY (channel not ready).

Reaction:

Mode group not ready.
The NC switches to follow-up mode.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Channel not ready.

Remedy:

Please inform the authorized personnel/service department. This alarm should not occur if the drive controller has been 

set correctly and the machining conditions are those that normally prevail.
- Check actual values: Local sluggishness of the carriage, speed dip by torque surge due to contact with workpiece/tool, 

travel against fixed obstacle, etc.
- Check direction of position control: Does the axis continue to rotate without control?

Programm 

continuation:

Restart part program.    Clear alarm with the RESET key in all channels of this mode group. Restart part program.

SINUMERIK 808D ADVANCED alarms
5.2 NCK alarms

Diagnostics Manual

342

Diagnostics Manual, 06/2015, 6FC5398-6DP10-0BA2

Summary of Contents for SINUMERIK 808D























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 808D

Sygonix 751848 Operating Instructions preview
751848
Brand: Sygonix Pages: 4
HIOS BLG-BC2-3010 Instruction Manual preview
BLG-BC2-3010
Brand: HIOS Pages: 2
Cameo SB 6T RDM User Manual preview
SB 6T RDM
Brand: Cameo Pages: 52
ABSINA 52-230-1001 Operating Manual preview
52-230-1001
Brand: ABSINA Pages: 12
Mitel MX-ONE Installation Manual preview
MX-ONE
Brand: Mitel Pages: 25
Hama T568A Instruction Manual preview
T568A
Brand: Hama Pages: 2
Hama 00053186 Operating Instructions Manual preview
00053186
Brand: Hama Pages: 50
Black Box Multi Quick Check RJ-11 Brochure & Specs preview
Multi Quick Check RJ-11
Brand: Black Box Pages: 3
C2G 81672 User Manual preview
81672
Brand: C2G Pages: 18
Grip SHW Assembly And Operating Manual preview
SHW
Brand: Grip Pages: 7
Pflueger Patriarch Manual preview
Patriarch
Brand: Pflueger Pages: 2
id-Technik K 26/38 Assembly Instructions preview
K 26/38
Brand: id-Technik Pages: 2
Larson Electronics EPP-30A-2P3W-1FT-L6.30 Instruction Manual preview
EPP-30A-2P3W-1FT-L6.30
Brand: Larson Electronics Pages: 3
Daxten MONITOR SPLITTER Brochure preview
MONITOR SPLITTER
Brand: Daxten Pages: 2
ULTIMATE SPEED USLK 22 B2 User Manual preview
USLK 22 B2
Brand: ULTIMATE SPEED Pages: 103
Nauticam M24A2R225 User Manual preview
M24A2R225
Brand: Nauticam Pages: 2
Velux ZZZ 241CM Manual preview
ZZZ 241CM
Brand: Velux Pages: 4
Emerson Easy Heat TSR Series Application Manual preview
Easy Heat TSR Series
Brand: Emerson Pages: 6

Brands by name

Popular brands

Load more brands