manualshive.com logo in svg

Siemens SINUMERIK 808D, Diagnostic Manual

The Siemens SINUMERIK 808D is an advanced CNC control system that offers precision and efficiency in machining. With its comprehensive Programming and Operating Manual, users can easily navigate and maximize the system's functionalities. Download the manual for free at 88.208.23.73:8080 and unlock the full potential of this groundbreaking product.

Share
Download
background image

Reaction:

Mode group not ready.
The NC switches to follow-up mode.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Channel not ready.

Remedy:

Please inform the authorized personnel/service department.
Check the setting parameters of the quadrant error compensation (friction compensation), if necessary switch off the 

compensation with MD32500 $MA_FRICT_COMP_ENABLE.

Programm 

continuation:

Restart part program.    Clear alarm with the RESET key in all channels of this mode group. Restart part program.

26002

Axis %1 encoder %2 parameterization error: number of encoder marks

Parameters:

%1 = Axis name, spindle number
%2 = Encoder number

Explanation:

1. Rotary measuring system (MD31000 $MA_ENC_IS_LINEAR[]==FALSE)
The number of encoder marks set in MD31020 $MA_ENC_RESOL[] does not correspond to the value in the drive machine 

data (PROFIdrive: p979) or zero has been entered in one of the two machine data.
2. Absolute measuring system with EnDat interface (MD30240 $MA_ENC_TYPE[]==4)
On absolute encoders, the resolution of the incremental and absolute tracks supplied by the drive is also checked for 

consistency.
For PROFIdrive drives:
Compare drive parameter p979 (and possibly other internal drive, manufacture-specific parameters stated in the relevant 

drive documentation) or compare images in NC-MDs $MA_ENC_RESOL, $MA_ENC_PULSE_MULT, 

$MA_ENC_ABS_TURNS_MODULO etc.
Conditions leading to triggering the alarm are:
* Number of encoder pulses in the drive!= $MA_ENC_RESOL
* PROFIdrive interface standardization/high resolution in p979 not permitted (permitted pushing factor 0...30 bits)
* With absolute encoders: Interface formats in p979 for absolute and incremental information does not fit together (i.e. the 

absolute position in XIST2 is supplied in too coarse resolution for a complete position reconstruction)
* In the case of rotary absolue encoders behind the gears (and activer traversing range extension in accordance with 

$MA_ENC_ABS_BUFFERING): Absolute position format (in Gx_XIST2) is complete/sufficient for position reconstruction 

via PowerOff in accordance with the following condition: $MA_ENC_RESOL*$MA_ENC_PULSE_MULT*

$MA_ENC_ABS_TURNS_MODULO must not be smaller than 2**32. A remedy against alarm triggering in the latter case 

may be to increase $MA_ENC_PULSE_MULT (or the associated drive-side parameterization e.g. p418/419 with 

SINAMICS) or (when the necessary conditions prevail) by deactivating the traversing range extension - see 

$MA_ENC_ABS_BUFFERING  

Reaction:

Mode group not ready.
The NC switches to follow-up mode.
Channel not ready.
NC Start disable in this channel.
Interface signals are set.
Alarm display.
NC Stop on alarm.
Channel not ready.

Remedy:

Please inform the authorized personnel/service department. 
Adjust machine data.
For absolute encoders, possibly pending drive alarms indicating encoder problems should be evaluated. They could be 

the cause of incorrect entries of MD1022 $MD_ENC_ABS_RESOL_MOTOR/MD1032 $MD_ENC_ABS_RESOL_DIRECT, 

which the drive reads out of the encoder itself.

Programm 

continuation:

Switch control OFF - ON.

SINUMERIK 808D ADVANCED alarms

5.2 NCK alarms

Diagnostics Manual

Diagnostics Manual, 06/2015, 6FC5398-6DP10-0BA2

347

Summary of Contents for SINUMERIK 808D























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 808D

XPOtool 62690 Operation Manual preview
62690
Brand: XPOtool Pages: 6
Microlab GPSS216 Quick Start Manual preview
GPSS216
Brand: Microlab Pages: 10
Monster SIRIUS ANTENNA EXTENSION CABLE User Manual preview
SIRIUS ANTENNA EXTENSION CABLE
Brand: Monster Pages: 7
ABSINA EV CHARGING CABLE MODE 2 Operating Manual preview
EV CHARGING CABLE MODE 2
Brand: ABSINA Pages: 29
NEC VT37 User Manual preview
VT37
Brand: NEC Pages: 75
NEC PlasmaSync 61XM4 Installation Manual preview
PlasmaSync 61XM4
Brand: NEC Pages: 10
NEC VT770 Series Service Manual Supplement preview
VT770 Series
Brand: NEC Pages: 7
NEC VT770 Series Brochure & Specs preview
VT770 Series
Brand: NEC Pages: 6
NEC VT37 Installation Manual preview
VT37
Brand: NEC Pages: 6
NEC WT600 Series Setup Manual preview
WT600 Series
Brand: NEC Pages: 99
NEC VT770 Series User Manual preview
VT770 Series
Brand: NEC Pages: 126
Philips SWV3431S/10 User Manual preview
SWV3431S/10
Brand: Philips Pages: 1
Philips SWV3430S/10 User Manual preview
SWV3430S/10
Brand: Philips Pages: 1
Philips SWV3431S Specification preview
SWV3431S
Brand: Philips Pages: 1
Philips SWV3303S/10 User Manual preview
SWV3303S/10
Brand: Philips Pages: 1
Philips SWV3302S/10 User Manual preview
SWV3302S/10
Brand: Philips Pages: 1
Philips SWV3312W Specifications preview
SWV3312W
Brand: Philips Pages: 2
Philips SWV3304W Specifications preview
SWV3304W
Brand: Philips Pages: 2

Brands by name

Popular brands

Load more brands