manualshive.com logo in svg

Siemens SINUMERIK 808D, Diagnostic Manual

The Siemens SINUMERIK 808D is an advanced CNC control system that offers precision and efficiency in machining. With its comprehensive Programming and Operating Manual, users can easily navigate and maximize the system's functionalities. Download the manual for free at 88.208.23.73:8080 and unlock the full potential of this groundbreaking product.

Share
Download
background image

Explanation:

 

Remedy:

For 840D sl - up to SW 2.6 SP1 and for 828D - up tp SW 4.3:
     - Specify different positions for the relevant points of _SETV[0...7] 
For 840D sl - as from SW 2.7 and for 828D - as from SW 4.4:
     - Specify different positions for the relevant points of P1(X1,Y1), P2(X2,Y2), P3(X3,Y3) and P4(X4,Y4). 

61368

[channel %1: ] block %2: straights through parameter %4 do not intersect

Parameters:

%1 = Channel number
%2 = Block number, label channel number

Explanation:

 

Remedy:

For 840D sl - up to SW 2.6 SP1 and for 828D - up tp SW 4.3:
     - Specify different positions for the relevant points of _SETV[0...7] 
For 840D sl - as from SW 2.7 and for 828D - as from SW 4.4:
     - Specify different positions for the relevant points of P1(X1,Y1), P2(X2,Y2), P3(X3,Y3) and P4(X4,Y4). 

61369

[Channel %1: ] Block %2: Position of corner not clearly definable, check parameter %4

Parameters:

%1 = Channel number
%2 = Block number, label channel number

Explanation:

 

Reaction:

Interpreter stop
NC Start disable in this channel.
Interface signals are set.
Alarm display.

Remedy:

For 840D sl - up to SW 2.6 SP1 and for 828D - up to SW 4.3:
     - Define P1 and P2 and/or P3 and P4 so that the intersection of the straights running through these points lies outside 

the sections formed by P1 and P2 and/or P3 and P4. 
For 840D sl - as from SW 2.7 and for 828D - as from SW 4.4:
     - Define P1(X1,Y1) and P2(X2,Y2) and/or P3(X3,Y3) and P4(X4,Y4 so that the intersection of the straights running 

through these points lies outside the sections formed by P1(X1,Y1) and P2(X2,Y2) and/or P3(X3,Y3) and P4(X4,Y4).

Programm 

continuation:

Clear alarm with the RESET key. Restart part program

61371

[Channel %1: ] Block %2: Product of column width and number of columns is greater than %4 

characters per line

Parameters:

%1 = Channel number
%2 = Block number, label channel number

Explanation:

 

Remedy:

Check user programming in cust_meaprot

61372

[Channel %1: ] Block %2: selected meas.variant requires SPOS-capable spindle

Parameters:

%1 = Channel number
%2 = Block number, label channel number

Explanation:

 

Remedy:

Change measuring variant or check machine equipment.

61373

[Channel %1: ] Block %2: No SPOS-capable spindle available

Parameters:

%1 = Channel number
%2 = Block number, label channel number

Explanation:

 

SINUMERIK 808D ADVANCED alarms
5.3 Cycle alarms

Diagnostics Manual

440

Diagnostics Manual, 06/2015, 6FC5398-6DP10-0BA2

Summary of Contents for SINUMERIK 808D























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SINUMERIK 808D

Hailink SP14NN00R User Manual preview
SP14NN00R
Brand: Hailink Pages: 6
BASETech 1490514 Operating Instructions Manual preview
1490514
Brand: BASETech Pages: 8
Kramer WP-211DS User Manual preview
WP-211DS
Brand: Kramer Pages: 15
MFJ MFJ-5124Y3 Instruction Manual preview
MFJ-5124Y3
Brand: MFJ Pages: 2
RIDGID 0095691665232 Operator'S Manual preview
0095691665232
Brand: RIDGID Pages: 12
BriskHeat PTBO-GET Instruction Manual preview
PTBO-GET
Brand: BriskHeat Pages: 20
Samcon SKDP03-T Mounting Manual preview
SKDP03-T
Brand: Samcon Pages: 12
Splitvolt SPS 01-011 Quick Start User Manual preview
SPS 01-011
Brand: Splitvolt Pages: 8
ReelCraft 7000 Series Operating Instructions preview
7000 Series
Brand: ReelCraft Pages: 4
OSCG OS-E1UF Manual preview
OS-E1UF
Brand: OSCG Pages: 3
Definitive Technology SCW-100 Owner'S Manual preview
SCW-100
Brand: Definitive Technology Pages: 16
BK TECHNOLOGIES BKR0608 User Instructions preview
BKR0608
Brand: BK TECHNOLOGIES Pages: 4
BK TECHNOLOGIES BKR0701 User Instructions preview
BKR0701
Brand: BK TECHNOLOGIES Pages: 8
Warmup NAMSRK-100FT Quick Start Manual preview
NAMSRK-100FT
Brand: Warmup Pages: 3
CYP CHDBT-1H7CE Operation Manual preview
CHDBT-1H7CE
Brand: CYP Pages: 16
CYP CHDBT-1H3CE Operation Manual preview
CHDBT-1H3CE
Brand: CYP Pages: 16
CYP CHDBX-1H1CE Operation Manual preview
CHDBX-1H1CE
Brand: CYP Pages: 16
Comtrol DB9 User Manual preview
DB9
Brand: Comtrol Pages: 26

Brands by name

Popular brands

Load more brands