06.03
10.5 Axes and spindles
10-376
Siemens AG, 2003. All rights reserved
SINUMERIK 840Di Manual (HBI) – 06.03 Edition
10.5.28 Spindle data
Table 10-47
Spindle: Machine data
Number
Identifier
Name
Ref.
General ($MN_ ...)
12060
OVR_SPIND_IS_GRAY_CODE
Spindle override, Gray-coded
V1
12070
OVR_FACTOR_SPIND_SPEED
Evaluation of the spindle speed override switch
V1
12080
OVR_REFERENCE_IS_PROG_FEED
Override reference speed
V1
Channel-specific ($MC_ ...)
20090
SPIND_DEF_MASTER_SPIND
Initial setting of master spindle in the channel
20092
SPIND_ASSIGN_TAB_ENABLE
Enable/disable spindle converter
20118
GEOAX_CHANGE_RESET
Permit automatic geometry axis change
22400
S_VALUES_ACTIVE_AFTER_RESET
S function effective with RESET
Axis-specific ($MA_ ...)
30300
IS_ROT_AX
Rotary axis
R2
30310
ROT_IS_MODULO
Modulo conversion
R2
30320
DISPLAY_IS_MODULO
Position display
R2
31050
DRIVE_AX_RATIO_DENOM
Load gear denominator
G2
31060
DRIVE_AX_RATIO_NUMERA
Load gear numerator
G2
31122
BERO_DELAY_TIME_PLUS
BERO delay time in plus direction
31123
BERO_DELAY_TIME_MINUS
BERO delay time in minus direction
32200
POSCTRL_GAIN
KV factor
G2
32810
EQUIV_SPEEDCTRL_TIME
Equivalent time constant of speed control loop
for feedforward control
K3
32910
DYN_MATCH_TIME.
Time constant of dynamic adaptation
G2
34040
REFP_VELO_SEARCH_MARKER
Reference shutdown speed
R1
34060
REFP_MAX_MARKER_DIST
Monitoring of zero reference mark distance
R1
34080
REFP_MOVE_DIST
Reference point distance/target position with
clearance-coded system
R1
34090
REFP_MOVE_DIST_CORR
Reference point offset/absolute offset
clearance-coded
R1
34100
REFP_SET_POS
Reference point value
R1
34200
ENC_REFP_MODE
Referencing mode
R1
35000
SPIND_ASSIGN_TO_MACHAX
Assignment of spindle to machine axis
35010
GEAR_STEP_CHANGE_ENABLE
Gear stage change possible
35012
GEAR_STEP_CHANGE_POSITION
Gear stage change position
35020
SPIND_DEFAULT_MODE
Spindle park position
35030
SPIND_DEFAULT_ACT_MASK
Activate spindle park position
35040
SPIND_ACTIVE_AFTER_RESET
Spindle activated by reset
35100
SPIND_VELO_LIMIT
Max. spindle speed
35110
GEAR_STEP_MAX_VELO[n]
Max. speed for gear stage change
35120
GEAR_STEP_MIN_VELO[n]
Min. speed for gear stage change
35130
GEAR_STEP_MAX_VELO_LIMIT[n]
Max. speed of gear stage
35140
GEAR_STEP_MIN_VELO_LIMIT[n]
Min. speed of gear stage
35150
SPIND_DES_VELO_TOL
Spindle speed tolerance
35160
SPIND_EXTERN_VELO_LIMIT
Spindle speed limiting from PLC
35200
GEAR_STEP_SPEEDCTRL_ACCEL[n]
Acceleration in speed control mode
Machine data
10 NC Start-Up with HMI Advanced