Table 2-21
Parameter in the Setting Dialog "Measurement Procedure", Mode of Operation 3-phase
Parameter
OPERRAT. MODE
=
3-phase
Parameter
MEAS. QUANTITY
=
Current
or
Voltage
Parameter
MEAS. METHOD
Fundamental
Only the fundamental harmonic is evaluated, higher harmonics are suppressed. This is
the standard measurement procedure of the protection functions.
Important: The voltage threshold value is always parameterized as phase-to-phase
voltage. If parameter
VOLTAGE SYSTEM
is selected as phase-to-ground, the voltage
threshold will be devided by
√
3.
True RMS
The "true" RMS value is determined, i.e. higher harmonics are evaluated. This procedure is
applied, for example, if an overload protection element must be realized on the basis of a
current measurement, as the higher harmonics contribute to thermal heating.
Important: The voltage threshold value is always parameterized as phase-to-phase
voltage. If parameter
VOLTAGE SYSTEM
is selected as phase-to-ground, the voltage
threshold will be devided by
√
3.
Positive seq.
,
Negative seq.
,
Zero sequence
In order to realize certain applications, the positive sequence system or negative
sequence system can be configured as measurement procedure. Examples are:
- I2 (tripping monitoring system)
- U2 (voltage asymmetry)
Via the selection zero sequence system, additional zero sequence current or zero
sequence voltage functions can be realized that operate independent of the ground varia-
bles IN and VN, which are measured directly via transformers.
Important: The voltage threshold is always parameterized according to the definition of
the balanced components independently of parameter
VOLTAGE SYSTEM
.
Parameter
MEAS. QUANTITY
=
Current
Parameter
MEAS. METHOD
Ratio I2/I1
The ratio of the negative-sequence current to the positive-sequence current is evaluated.
Please note that the function only operates if
Ι
2 or
Ι
1 has exceeded the threshold value
0.1 ·
Ι
N
.
Parameter
MEAS. QUANTITY
=
Voltage
Parameter
VOLTAGE
SYSTEM
Phase-Phase
Phase-Ground
If phase-to-ground voltages are connected to the device (see parameter address 213
VT
Connect. 3ph
), it can be selected whether a three-phase operating voltage function
must evaluate the phase-to-ground or phase-to-phase voltages.
When selecting phase-to-phase, these variables are derived from the phase-to-ground
voltages. The selection is, for example, important for single-pole faults. If the faulty
voltage drops to zero, the affected phase-to-ground voltage is thus zero, and the respec-
tive phase-to-phase voltages drop to the variable of a phase-to-ground voltage.
With phase-to-phase voltage connection the parameter is hidden.
Functions
2.19 Flexible Protection Functions
SIPROTEC 4, 7SJ62/64, Manual
275
C53000-G1140-C207-8, Edition 08.2016
Summary of Contents for SIPROTEC 4
