)NSTALLATION INSTRUCTIONS
3*
6
# ' #
-ARSHALLING OF BINARY INPUTS BINARY OUTPUTS AND ,%$ INDICATORS
)NTRODUCTION
4HE FUNCTIONS OF THE BINARY INPUTS AND OUTPUTS REPRE
SENTED IN THE GENERAL DIAGRAMS !PPENDIX ! RELATE
TO THE FACTORY SETTINGS 4HE ASSIGNMENT OF THE OUT
PUTS AND A PART OF THE INPUTS OF THE INTERNAL FUNCTIONS
CAN BE REARRANGED AND THUS ADAPTED TO THE ON SITE
CONDITIONS $EPENDENT OF THE SELECTED FEEDER MIMIC
DIAGRAM A PART OF THE BINARY INPUTS IS FIXEDLY AS
SIGNED TO THE AUXILIARY CONTACTS OF THE SWITCHING ELE
MENTS THESE CANNOT BE ALTERED !PPENDIX % SHOWS
THE AVAILABLE FEEDER MIMIC DIAGRAMS AND THE AS
SIGNED BINARY INPUTS
7HEN THE 3* PROGRAMS ARE RUNNING THE SPECIFIC
LOGIC FUNCTIONS WILL BE ALLOCATED TO THE PHYSICAL INPUT
AND OUTPUT MODULES OR ,%$S IN ACCORDANCE WITH THE
SELECTION
%XAMPLE
&AULT DETECTION IS REGISTERED FROM THE
OVERCURRENT PROTECTION 4HIS EVENT IS GENERATED IN
3* AS AN ANNUNCIATION LOGICAL FUNCTION AND
SHOULD BE AVAILABLE AT CERTAIN TERMINALS OF THE UNIT AS
A ./ CONTACT 3INCE SPECIFIC UNIT TERMINALS ARE
HARD WIRED TO A SPECIFIC PHYSICAL SIGNAL RELAY EG
TO THE SIGNAL RELAY THE PROCESSOR MUST BE ADVISED
THAT THE LOGICAL SIGNAL
$EVICE <$ET
SHOULD BE
TRANSMITTED TO THE SIGNAL RELAY 4HUS WHEN MAR
SHALLING IS PERFORMED TWO STATEMENTS OF THE OPERATOR
ARE IMPORTANT
7HICH
LOGICAL ANNUNCIATION GENER
ATED IN THE PROTECTION UNIT PROGRAM SHOULD TRIGGER
WHICH
PHYSICAL SIGNAL RELAY 5P TO LOGICAL AN
NUNCIATIONS CAN TRIGGER ONE PHYSICAL SIGNAL RELAY
! SIMILAR SITUATION APPLIES TO BINARY INPUTS WHICH
CAN BE FREELY ASSIGNED IE WHICH ARE NOT ASSIGNED
TO THE AUXILIARY CONTACTS OF SWITCHING ELEMENTS )N
THIS CASE EXTERNAL INFORMATION EG BLOCKING OF STAGE
) IS CONNECTED TO THE UNIT VIA A PHYSICAL INPUT
MODULE AND SHOULD INITIATE A LOGICAL FUNCTION
NAMELY BLOCKING 4HE CORRESPONDING QUESTION TO THE
OPERATOR IS THEN
7HICH
SIGNAL FROM A PHYSICAL IN
PUT RELAY SHOULD INITIATE
WHICH
REACTION IN THE DE
VICE /NE PHYSICAL INPUT SIGNAL CAN INITIATE UP TO
LOGICAL FUNCTIONS
4HE TRIP RELAYS CAN ALSO BE ASSIGNED DIFFERENT FUNC
TIONS %ACH TRIP RELAY CAN BE CONTROLLED BY A COM
MAND FUNCTION OR COMBINATION OF COMMAND FUNC
TIONS
4HE LOGICAL ANNUNCIATION FUNCTIONS CAN BE USED IN
MULTIPLE MANNER %G ONE ANNUNCIATION FUNCTION CAN
TRIGGER SEVERAL SIGNAL RELAYS SEVERAL TRIP RELAYS ADDI
TIONALLY BE INDICATED BY ,%$S AND BE CONTROLLED BY A
BINARY INPUT UNIT 4HE RESTRICTION IS THAT THE TOTAL OF ALL
PHYSICAL INPUTOUTPUT UNITS BINARY INPUTS PLUS SIGNAL
RELAYS PLUS ,%$S PLUS TRIP RELAYS WHICH ARE TO BE AS
SOCIATED WITH ONE LOGICAL FUNCTION MUST NOT EXCEED A
NUMBER OF
)F THIS NUMBER IS TRIED TO BE EXCEEDED
THE DISPLAY WILL SHOW A CORRESPONDING MESSAGE
4HE MARSHALLING PROCEDURE IS SET UP SUCH THAT FOR
EACH PHYSICAL BINARY INPUT EACH OUTPUT RELAY AND
FOR EACH MARSHALLABLE ,%$ THE OPERATOR WILL BE
ASKED WHICH LOGICAL FUNCTION SHOULD BE ALLOCATED
4HE OFFERED LOGICAL FUNCTIONS ARE TABULATED FOR THE
BINARY INPUTS OUTPUTS AND ,%$S IN THE FOLLOWING SEC
TIONS
-ARSHALLING OF THE INPUTS OUTPUTS AND ,%$S IS PER
FORMED BY MEANS OF THE INTEGRATED OPERATOR PANEL OR
VIA THE OPERATING INTERFACE IN THE FRONT -ARSHALLING
BEGINS AT THE PARAMETER ADDRESS
4HE INPUT OF THE CODE WORD OF CODE LEVEL IS REQUIRED
FOR MARSHALLING REFER 3ECTION 7ITHOUT CODE
WORD ENTRY PARAMETERS CAN BE READ OUT BUT NOT BE
CHANGED $URING CODE WORD OPERATION IE FROM
CODE WORD ENTRY UNTIL THE TERMINATION OF THE MARSHAL
LING PROCEDURE THE SOLID BAR IN THE DISPLAY FLASHES
4HE BEGINNING OF THE MARSHALLING PARAMETER BLOCKS
IS REACHED BY DEPRESSING THE
-%.5
KEY THE /0
%2!4)/. -%.5 APPEARS 3INCE THE TOTAL MENU
TAKES MORE THAN ONE DISPLAY PAGE THE DOUBLE AR
ROW KEY
IS USED TO PAGE TO /0%2!4)/. -%.5
USE THE KEY
TO PAGE BACK 7ITHIN THE MENU A
MENU OPTION IS SELECTED BY ENTERING THE ASSIGNED
DIGIT REFER TO &IGURE &INALLY THE SUB MENU
WITH THE CONFIGURATION ADDRESS BLOCKS IS DISPLAYED
4HE ADDRESSES ARE DEFINED BY THE FOUR DIGIT AD
DRESS NUMBER EG AND THE HEADING OF THE AD
DRESS BLOCK EG -!23(!,,).' ").!29 ).0543
4HE PREVIOUS MENU CAN BE REACHED WITH THE BACK
SPACE KEY
2
)F THE
2
KEY IS PRESSED ON THE LEVEL OF
THE MAIN MENU THE BASIC DISPLAY WILL APPEAR )F THE
-%.5
KEY IS PRESSED THE FIRST MAIN MENU AP
PEARS
www
. ElectricalPartManuals
. com
