background image

en 

Troubleshooting

52

Fault

Cause

Troubleshooting

All LEDs lit up or flashing.

Electronics have detected a
fault.

1.

Press the main switch button for ap-
prox. 4 seconds.

→ 

"Controls", Page 15

The appliance is reset and restar-
ted.

2.

If the problem occurs again:

Switch off the appliance.

Pull out the mains plug or
switch off the fuse in the fuse
box.

Wait at least 2 minutes.

Switch on the fuse in the fuse
box or insert the mains plug.

Switch the appliance on.

3.

If the problem occurs again:

Contact customer service.

→ 

"Customer Service",

Page 55

Mechanical damage

Fault

Cause

Troubleshooting

Appliance door cannot be
closed.

Door lock has been activ-
ated.

Close the appliance door with
greater force.

Door cannot be closed due
to installation method.

Check whether the appliance has
been installed properly.
When closed, the appliance door,
its decor or attached parts should
not knock against adjacent cabin-
ets or the worktop.

Lid on the detergent dis-
penser cannot be closed.

Detergent dispenser or lid
are blocked by sticky deter-
gent residue.

Remove detergent residue.

Noise

Fault

Cause

Troubleshooting

Filling valves making knock-
ing noises.

Caused by the domestic in-
stallation. No appliance fault
present. Does not affect
functioning of the appliance.

Can only be remedied in the do-
mestic installation.

Knocking or rattling noise.

Spray arm is striking table-
ware.

Arrange tableware so that the spray
arms do not strike tableware.

Summary of Contents for SN61HX08VE





























































Reviews: