34
Figure
●
Push the telescopic tube into the connecting piece
on the floor tool until it locks in place.
●
To release the connection, press the locking collar
and pull out the telescopic tube.
Figure
●
Move the sliding sleeve in the direction of the arrow
to release the telescopic tube and adjust it to the
length required.
Figure
●
Holding the power cord by the plug, pull out to the
required length and insert the plug into the mains
socket.
!
After continuous use of more than 30 minutes,
completely disconnect the power cord from the
power supply.
=> Risk of overheating and subsequent damage.
Figure
Switching on and off
●
To switch the vacuum cleaner on or off, press the
ON/OFF button.
Figure
Controlling the suction level
The required suction level can be set to the level
required by turning the control knob in the direction
of the arrow.
Low power range
=>
For vacuuming delicate materials,
such as upholstery, curtains, etc.
Medium power range
=>
For the daily vacuuming of light dirt deposits.
High power range
=>
For vacuuming durable floor coverings,
hard floors and heavily soiled surfaces.
Vacuuming
!
Please note:
Floor tools are subject to a certain amount of
wear,depending on the type of hard floor you have
(e.g. rough, rustic tiles). Therefore, you must check
the underside of the floor tool at regular intervals.
Worn undersides of floor tools may have sharp edges
that can damage sensitive hard floors, such as
parquet or linoleum. The manufacturer does not
accept any responsibility for damage caused by worn
floor tools.
Figure
Adjusting the floor tool:
Rugs and carpets
=>
hard floors
=>
Figure
●
Remove the crevice nozzle or upholstery nozzle from
the accessories compartment in the appliance lid.
6*
7
5*
8
9
10
11
Figure
Vacuuming with accessories
Attach the nozzles to the suction pipe or handle as
required:
a)
Crevice nozzle for vacuuming crevices and corners,
etc.
b)
Upholstery nozzle for vacuuming upholstered
furniture, curtains, etc.
c)
Hard-floor tool
For vacuuming hard floor coverings
(tiles, parquet flooring, etc.)
●
Push the telescopic tube into the connecting piece
of the hard floor tool until it locks in place.
●
To release the connection, press the locking collar
and pull out the telescopic tube.
Figure
●
After use, place the crevice or upholstery nozzle back
into the accessories compartment in the appliance
lid.
Turbo brush
If your appliance is equipped with a turbo brush,
please consult the accompanying instruction manual
for instructions on its use and maintenance.
Figure
●
You can use the nozzle parking aid on the back of the
appliance if you wish to stop vacuuming for a short
time.
●
Once you have switched off the appliance, slide the
hook on the floor tool into the recess on the rear of
the appliance.
Figure
To overcome obstacles, e.g. steps, the appliance can
also be carried by the handle on the appliance body.
When you have finished vacuuming
Figure
●
Pull out the mains plug.
●
Briefly pull the power cord and release
(The power cord rewinds automatically).
Figure
●
To store or transport the appliance, you can use the
storage aid on the underside of the appliance.
●
Stand the appliance upright. Slide the catch on the
floor tool into the groove on the underside of the
vacuum cleaner.
Changing the filter
!
Please note: Always switch off the appliance before
changing the filter.
13
12
14
15
16
17
*depending on model
Summary of Contents for VSZ4G130
