background image

Overview of programmes       

en

17

*** 

Hygienic

Hard-wearing fabrics made of cotton or linen

Note:  

Particularly suited to washing items that need to be hygien-

ically clean and especially kind to sensitive skin thanks to the long-

er wash cycle at a defined temperature, higher water level and 

longer spin cycle.

Max. 7 kg/5* kg

Ž

 - 60 °C

$

 - 1600** rpm

ecoPerfect 

¦

, speedPerfect 

G

Less Ironing,
Rinse Plus

*** 

Outdoor / Impregnation

Wash cycle followed by waterproofing of membrane-coated 

weatherproof and outdoor clothing or water-resistant fabrics

1.

Select a programme.

2.

Add special detergent for outdoor clothing to compartment 

II

.

3.

Add waterproofing agent (max. 170 ml) to compartment 

i

.

4.

Press the 

Ü

 button. After-treat the laundry in accordance 

with the manufacturer's instructions.

Notes

Use a special detergent suitable for machine washing and 

dose in accordance with the manufacturer's instructions:

Laundry must not be treated with fabric softener.

Before washing, clean the detergent drawer thoroughly (all 

compartments) to remove fabric-softener residue.

Max. 1 kg

Ž

 - 40 °C

$

 - 800 rpm

ecoPerfect 

¦

, speedPerfect 

G

Rinse Plus

*** 

Outdoor

Membrane-coated weatherproof or outdoor clothing and water-

resistant fabrics

Notes

Use special detergent suitable for machine washing; add the 

correct dosage to compartment 

II

 in accordance with the 

manufacturer's instructions.

Laundry must not be treated with fabric softener.

Before washing, clean the detergent drawer thoroughly (all 

compartments) to remove fabric-softener residue.

Max. 2 kg

Ž

 - 40 °C

$

 - 800 rpm

ecoPerfect 

¦

, speedPerfect 

G

Rinse Plus

*** 

Sports / Fitness

Sportswear and leisurewear made from microfibre fabrics;

Notes

Laundry must not be treated with fabric softener.

Before washing, clean the detergent drawer thoroughly (all 

compartments) to remove fabric-softener residue.

Max. 2 kg

Ž

 - 40 °C

$

 - 800 rpm

ecoPerfect 

¦

, speedPerfect 

G

Less Ironing,
Rinse Plus

Programme/type of laundry/information

Settings

*  Reduced load for the 

speedPerfect 

G

 setting

**  Max. spin speed, depending on the model

***  Programme depending on the model

Summary of Contents for WM14W440AU













































Reviews: