background image

Cleaning and maintenance       

en

31

Note:  

To prevent unused detergent 

from flowing straight into the drain 

during the next wash: Pour 1 litre of 

water into compartment 

II

 and start the 

Empty

 programme.

The drain hose at the siphon 

is blocked

1.

Switch off the appliance. Pull out the 

mains plug.

2.

Loosen the hose clamp. Carefully 

remove the drain hose; residual 

water may leak out. 

3.

Clean the drain hose and siphon 

connecting piece.

4.

Re-attach the drain hose and secure 

the connection point using the hose 

clamp.

Filter in the water supply 

blocked

First, reduce the water pressure in the 

supply hose:

1.

Turn off the tap.

2.

Select any programme  (except 

Rinse/Spin/Empty).

3.

Press the 

Ü

 button. Allow the 

programme to run for approximately 

40 seconds.

4.

Press the 

#

 button. The appliance is 

switched off.

5.

Pull out the mains plug.

Then clean the filter:

1.

Disconnect the hose from the tap.

Clean the filter with a small brush.

2.

For standard and Aqua-Secure 

models, clean the filter on the rear of 

the appliance:

Remove the hose from the rear of 

the appliance.

Use pliers to remove the filter and 

then clean it.

3.

Connect the hose and check for 

leaks.

Summary of Contents for WM14W540EU

















































Reviews: