background image

NLTroubleshooting

Malfunction

Cause and Troubleshooting

▶ 

No error - no action required.

The program duration

changes during the wash 

cycle.

Remark:When loading, place large and small items of 

laundry together in the drum. Different sized laundry 

is more evenly distributed during the spin cycle.

Foam control system provides an extra rinse when 

foaming is too high.

▶ 

No error - no action required.

The water is not 

visible in the drum

bar.

The water is below visible range.

No error - no action required.

▶ 

Do not fill the device with additional water during 

operation.

Drum jerks after

program start.

The cause is an internal motor test.

▶ 

No error - no action required.

Vibration and movement

of the appliance 

during the spin

run.

The appliance is not leveled properly.

▶ 

"Adjusting the device", Page 17

Device feet are not fixed.

▶ 

Secure the device feet.

"Adjusting the device", Page 17

Transport protections have not been removed.

▶ 

"Remove transport locks", page 14.

Drum is spinning, er

no water flows into 

the appliance.

Load recognition is active.

▶ 

No error, no action necessary.

Remark:The load detection can take up to 2 minutes.

strong foam

ming.

Detergent dosage is too high.

▶ 

Immediate measure: mix a tablespoon of fabric 

softener with 0.5 l of water and pour this mixture into 

the manual dosing compartment (not for outdoor, 

sportswear and down textiles).

When the intelligent dosing is activated, reduce the 

basic dosing amount

Page 38.

▶ 

When dosing manually, reduce the amount of 

detergent for the next wash with an equal load.

i-Dos

cannot be pressed

i-Dos

Intelligent dosing is not possible for this program.

▶ 

No error - no action required.

"Start program with intelligent dosing system", 

page 36

52

Summary of Contents for WM16XK75NL

































































Reviews: