background image

NLIntelligent dosing system

In order not to cancel the current 

program, the program selector 

must be set to the initial program.

sFill the detergent or detergent

softer in the manual dosing 

dispenser.

"Dosing detergent and care 

agent", Page 34 sActivate the 

intelligent dosing system

tem after the program end.

"Buttons", Page 25

agoes out in the display

.

15 Intelligent dosing system

teem

Requirements

sThe laundry is prepared.

"Preparing the laundry", 

Page 32

sThe laundry is sorted. sThe 

laundry has been placed.

"Filling the drum with laundry", 

Page 34

sThe program is set.

"Set program", page 33

sThe intelligent dosing system is

activated.

"Buttons", Page 25

"Display", page 23

"Display", page 23

Depending on the program and the 

settings, the optimum amounts of 

liquid detergent and fabric softener 

are dosed automatically.

15.1 Program with intelligent 

dosing system

start

If you do not want to manually dose 

liquid detergent and fabric softener, 

use the intelligent dosing system. This 

function is available depending on the 

program set and is activated 

automatically.

1.

Fill the dosing containers.

"Filling the dosing 

container", page 37

Remark

If you use the intelligent dosing 

system, do not add additional 

detergent or fabric softener to the 

manual dosing dispenser.

"Dosing detergent and care agent", 

Page 34

If you want to dose manually for a set 

program, please observe the 

following instructions: sDeactivate the 

intelligent dosing

system before starting the 

program. The settings are saved 

even after the device is switched 

off.

"Buttons", Page 25

To replace the contents of the 

dosing containers with another 

product, clean the detergent 

drawer.

"Cleaning the detergent 

drawer", Page 40

2.

If desired, the contents of the 

dosing containers 

Page 37 To 

adjust.

3.

If desired, the basic dosing amount 

Page 38To adjust.

4.

If desired, adjust the program 

settings.

"Adjust program settings", page 

33

5.

Start the program.

"Starting the program", Page 

34

36

Summary of Contents for WM16XK75NL

































































Reviews: