background image

Avoid material damage NL

▶ 

Make sure that the internal 

diameter of the water tap is at least 

17 mm.

▶ 

Make sure that the thread length 

on the connection to the water 

tap is at least 10 mm.

Water pressure that is too low or too high can 
interfere with the appliance function.

▶ 

Make sure that the water pressure 

on the water supply system is at 

least 100 kPa (1 bar) and at most 

1000 kPa (10 bar).

▶ 

If the water pressure exceeds the 

specified maximum value, a 

pressure reducing valve must be 

installed between the drinking 

water connection and the hose set 

of the device.

▶ 

Do not connect the appliance to the 

mixer tap of a pressureless water 

heater or boiler.

Modified or damaged water hoses can 

lead to material damage and damage 

to the device.

▶ 

Never kink, pinch, modify or cut 

water hoses.

▶ 

Only use supplied water hoses or 

original spare hoses.

▶ 

Reuse never used water hoses.

Use with contaminated or too hot 

water can cause material damage and 

damage to the device.

▶ 

Operate the device only with cold 

tap water.

Unsuitable cleaning agents can 

damage the surfaces of the device.

▶ 

Do not use sharp or abrasive 

cleaning agents.

▶ 

Do not use strong alcohol-based 

cleaning agents.

▶ 

Do not use hard scouring or 

dishwashing sponges.

2 Material damage

avoid

Follow this instruction to avoid 

material damage and damage to the 

device.

PAY ATTENTION!

Incorrect dosage of fabric softeners, 

detergents, care products and 

cleaning agents can affect the 

functioning of the appliance.

▶ 

Follow the manufacturer's dosing 

recommendations.

Exceeding the maximum load 

quantity affects the operation of the 

appliance.

▶ 

Observe and do not exceed the 

maximum load for each 

programme.

→ 

"Programs", Page 27

The device is secured for transport 

with transport locks. Transport locks 

that have not been removed can lead 

to material damage and damage to 

the device.

▶ 

Before commissioning, remove and 

store all transport locks completely.

▶ 

Before each transport, install all 

transport locks completely to avoid 

transport damage.

Improper connection of the water 

inlet hose can lead to material 

damage.

▶ 

Tighten the screw connections on 

the water supply hand-tight.

▶ 

It is best to connect the water inlet 

hose directly to the water tap 

without additional connecting 

elements such as adapter, 

extension, valve or the like.

▶ 

Make sure that the valve housing of 

the water inlet hose is installed 

without contact with the 

environment and that it is not 

exposed to external forces.

11

Summary of Contents for WM6HXK76NL





































































Reviews: