background image

en

        Faults and what to do about them

44

3.

Drain the water. 

~

 Page 41

4.

Pull the emergency release 

downwards with a tool and release.

The door can then be opened.

Information on the display panel

Display

Cause/Remedy

Õ

 

Flashes fast + signal

: The door was opened and the water level is too high. 

Close the door, continue the programme with 

inicio/pausa+carga (Start/

Reload)

  button or select 

p

  (Drain)

.

Flashes slowly

: The door lock temperature is too high to open the door. Wait 

approx. 30 seconds until the door lock temperature cools down.

•©£

The temperature in the drum is too high. Wait for the appliance running to cool 

down the laundry till the 

•©£

 disappears on the display panel, then the door can 

be opened.

|

 

Flashes

 (no water supply): Water tap turned on? Filter in the water supply is 

blocked? 

~

 "Filter in the water supply is blocked" on page 42

 

Is the supply hose kinked or trapped?

Lights up 

(low water pressure): For information only. This will not affect the 

programme progress. The programme duration is extended.

w

 lights up

The childproof lock is activated – deactivate it.

The symbol 

k

 

flashes

Run the 

algodón/algodão 90°C (Cottons 90°C)

 programme to clean and care for 

the drum and the outer tub.

Notes

Run the programme without laundry.

Use washing powder or a detergent containing bleach. To prevent foaming, 

only use half the amount of detergent recommended by the detergent manu-

facturer. Do not use detergent designed for woollens or delicates.

Switching the drum care information signal on/off. 

~

 Page 39

E:36

  

alternating with  

-10

Drain pipe or water drain hose is blocked. Clean the drain pipe and the water 

outlet hose. 

Drain pipe or water drain hose is caught or jammed. Ensure that the drain pipe 

and water drain hose are not kinked or trapped.

The drain pump is blocked. 

 

~

 "Drain pump is blocked" on page 41

The drain hose at the siphon is blocked. 

 

~

 "The drain hose at the siphon is blocked" on page 42

The water drain hose is connected too high. Install the water outlet hose at a 

maximum height of 1 meter. 

~

 Page 16

Summary of Contents for WN44G200ES





















































Reviews: