background image

en

    Draining the condensation water

38

6.

Secure the other side of the drain 

hose using the remaining 

accessories, depending on the 

connection situation.

Washbasin:

Siphon:

The connection point must be 

secured using a hose clamp (12-

22 mm clamping range, available 

from specialist retailers).

When connecting to a siphon, make 

sure that the drain hose is routed at 

a height of at least 80 cm, but no 

more than 100 cm.

Floor drain:

Caution!

Risk of material damage due to 

leaks or draining water.

Secure the drain hose to prevent it 

from slipping out. Do not kink or 

bend the drain hose. The height 

difference between the surface on 

which the appliance is installed and 

the drain hose must be no more than 

100 cm.

Caution!

Risk of accumulated water being 

drawn back into the appliance and 

causing material damage.

Check that the water drains away 

quickly. The drain must not be 

sealed or blocked.

7.

Pull out the condensation container 

horizontally and empty it.

8.

Turn the condensation container 

180° onto its underside and remove 

the stopper that is fitted.

Summary of Contents for WT47W591GB





















































Reviews: