background image

7/8 

Building Technologies 

Network Node WTT16…, WTX16… 

CE1N2874en 

HVAC Products 

 

14.07.2005 

as a confirmation. The result would be an erroneous display when showing the remain-
ing capacity. 
 
First, remove the discharged main battery and insert the new one. Press the blue 
DISPLAY button once to start the life expectancy calculation for the new main battery. 
The backup battery MUST NOT be removed simultaneously. A fatal loss of data would 
happen. 
 
After storing the main battery for longer periods, especially at temperatures higher than 
30 °C, the battery might passivate. Under these circumstances it will not be able to 
deliver sufficient energy to the network node. If the network node detects a passivated 
battery a de-passivation cycle is triggered. This is indicated by a flashing front LED. 
The procedure might take a few minutes. After de-passivation the network node will 
start up in IdLE   mode. Low temperatures at the battery may cause a similar behavior 
in other modes too. 
 
The main battery used by the WTT16… requires careful treatment: 

  Do not short-circuit or damage the battery 

  Do not expose the battery to excessive heat 

  Return exhausted batteries to the supplier 

  Read the enclosed safety instructions carefully 

M-Bus connection 

Any network node can be connected to the M-Bus temporarily (service connector) or 
continuously (screw terminal for the fixed M-bus connection). A plug for the screw ter-
minal is included with every network node. 

RESET

MODE

Screw terminal for the fixed

M-Bus connection

max. 5 unit loads

 M-Bus  service connection

 

Technical data 

 conformity to EMC directives 

 

Safety class  

IP32 

Safety class  

Electromagnetic compatibility 

immunity:  EN 55 024/EN 301 489 
emissions:  EN 55 022/EN 300 220-1 

Operating voltage WTT16… 

DC 3.6 V 

Lifetime of main battery 

> 5 years 

Operating voltage WTX16… 

AC 100…240 V, 50/60Hz 

Rated frequency  

868.3 MHz  

Transmitter power  

< 14 dBm  

Frequency of transmission 

<1% 

Perm. ambient temperature  
 

Transport and storage 

 Operation 

 

20…+60 °C (< 30°C recommended) 

0…55 °C 

Weight 

0.3 kg  

 

Battery replacement 

De-passivation 

Safety notes on  
lithium batteries 

Summary of Contents for WTT16 Series









Reviews: