background image

en

        Faults and what to do about them

30

Remove hose from the rear of the 

appliance. 

Take out filter with pliers and clean.

6.

Connect the hose and check for 

leaks.

3

Faults and what to do 

about them

Fau

lt

and

 

wha

to 

do 

abo

ut

 

the

m

Emergency release, e.g. if a 

power failure occurs

The programme continues running 

when the power supply is restored. If 

the washing is still to be removed, the 

door can be opened as described 

below:

:

Warning

Danger of scalding!

Wash liquor and washing may be hot. 

If touched, there is a risk of scalding.

If required, leave to cool down.

Caution!

Danger when reaching into/gripping 

the rotating drum!

If you reach into the rotating drum, you 

may injure your hands.

Do not grip the rotating drum. Wait until 

the drum stops rotating.

Caution!

Water damage possible!

Leaking water may cause damage.

Do not open the door if you can still see 

water through the glass.

1.

Switch off the appliance. Pull out the 

mains plug.

2.

Drain the water.

 

3.

Pull down emergency release with 

a tool and release.

Door can then be opened.

Summary of Contents for XQG90-WM14S7600W













































Reviews: