Sierra Wireless AirPrime WP8548 Hardware Integration Manual Download | Manualshive

Page: 4 / 26

background image

Hardware Integration Guide

Specifications subject to change

4

4118723

Patents

This product may contain technology developed by or for Sierra Wireless Inc.

This product includes technology licensed from QUALCOMM

®

.

This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under
one or more patents licensed from InterDigital Group and MMP Portfolio
Licensing.

Copyright

©2016 Sierra Wireless. All rights reserved.

Trademarks

Sierra Wireless

®

, AirPrime

®

, AirVantage

®

, Skylight™, and the Sierra Wireless

and Open AT logos are registered trademarks of Sierra Wireless, Inc. or one of its
subsidiaries.

Windows

®

is a registered trademark of Microsoft Corporation.

QUALCOMM

®

is a registered trademark of QUALCOMM Incorporated. Used

under license.

Other trademarks are the property of their respective owners.

Contact
Information

Consult our website for up-to-date product descriptions, documentation,
application notes, firmware upgrades, troubleshooting tips, and press releases:

www.sierrawireless.com

Revision
History

Sales Desk:

Phone:

1-604-232-1488

Hours:

8:00

AM

to 5:00

PM

Pacific Time

Contact:

http://www.sierrawireless.com/sales

Post:

Sierra Wireless
13811 Wireless Way
Richmond, BC
Canada V6V 3A4

Technical support:

support@sierrawireless.com

RMA support:

repairs@sierrawireless.com

Fax:

1-604-231-1109

Web:

www.sierrawireless.com

Revision
number

Release date

Changes

1

February 2016

FCC / IC certification

2

February 2016

Removed trace diagrams from Chapter 4; added point #6 (for RF trace design) to

Important Compliance Information for North American Users on page 22

.

«
...
2
3
4
5
6
...
»

Summary of Contents for AirPrime WP8548



























Reviews:

No comments

Related manuals for AirPrime WP8548

Brand: Panasonic Pages: 45

Brand: Ohsung Electronics Pages: 18

ESD-5550 Series

Brand: GAC Pages: 12

Brand: Parker Pages: 38

Brand: Parker Pages: 2

Brand: M-system Pages: 13

MT600iWP Series

Brand: weintek Pages: 2

Brand: IR-Tec Pages: 14

Brand: Cypress Pages: 3

IB-TRON 4000 SOL

Brand: INSBUD Pages: 14

Brand: Rational Pages: 140

Brand: Euromatic Pages: 20

Brand: VMK Pages: 98

AQUIS ULTRAFLOW

Brand: Waterous Pages: 217

PersonalWorkplace Pro Video

Brand: G&D Pages: 56

Brand: Beninca Pages: 16

Brand: Woodward Pages: 118

Brand: Osaka Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands