SIG FOUR-STAR 40 ARF Assembly Manual Download | Manualshive

Page: 3 / 16

background image

.

Complete Kit Parts List

The following is a complete list of all parts contained in this kit. Before beginning assembly, we suggest that you take the time to
inventory the parts in your kit.

Basic Aircraft Parts

1 Fuselage

1 Right & Left Wing Panel Set

with Ailerons.

1 Horizontal Stabilizer & Elevator Set.

1 Vertical Fin & Rudder Set

Wire Parts

1 Formed Elevator Joiner Wire

1 Formed Tailwheel Wire with

Hinge

Hardware

2 Nylon Control Horn with Back

Plate; Elevator & Rudder

4 M2 x 15mm Horn Mounting

Screws

1 5.3mm x 320mm Nylon Throttle

Pushrod Housing

1 3.2mm x 280mm Nylon Throttle

Pushrod

2 5.3mm x 521mm Nylon

Pushrod Housing elevator &
rudder

2 3.2mm x 686mm Nylon

Pushrod elevator & rudder

2 M4 x 15mm Phillips Head Screws; for

main landing gear attachment

2 M4 Split Lock Washer; for main

landing gear attachment

4 M3 x 20mm Phillips Head

Screws; for motor & mount
attachment

4 M3 Flat Washers; for mount to

firewall

4 M3 Split Lock Washer; for mount to

firewall

1 2mm id Wheel Collar with set

screws; for Tail Wheel

2 M4 x 40mm Phillips Head

Screws; main wheel axles

4 M4 Lock Nuts; for axles

2 M4 Hex Nuts; for axles

4 M3 x 10mm Phillips Head Screws;

Wheel Pant mounting

4 M3 Split Lock Washers; Wheel

Pant mounting

2 1/4-20 x 1-1/2”Nylon Wing

Bolts; for wing mounting

5 2mm Nylon R/C Links; for elevator

(1), rudder (1), throttle (1), ailerons
(2)

5 2mm Solder R/C Links; for

elevator (1), rudder (1), throttle
(1), ailerons (2)

2 2mm x 200mm Pushrod; for

aileron (2)

4 2mm x 20mm threaded stud;

for elevator (1), rudder (1),
throttle (2)

2 2mm x 100mm Pushrod; for elevator

(1),rudder (1)

Miscellaneous

1 3mm Formed Aluminum Main

Landing Gear

1 Molded Clear Plastic Canopy

1 2 pc. Adjustable Motor Mounts, 40-

size

2 7.0cm dia. (approx. 2 3/4”) Main

Wheels

1 25mm dia. (approx. 1”)

Tailwheel

1 2” dia. Spinner assembly

1 260cc (8.7oz) Fuel Tank Assembly

1 Left Wheel Pant

1 Right Wheel Pant

17 CA Hinges; for ailerons (9),

elevator (6), rudder (3)

1 10mm Hardwood Wing Joiner

1 3mm Plywood Aileron Servo Tray

1 8mm x 20mm x 76mm Balsa;

Fuel Tank Retainer

2 10mm x 124mm Balsa

Triangle; Rudder Fairings

1 3mm x 15mm x 23mm

Plywood;Throttle Pushrod Anchor

1 3/8” x 12” Iron On Covering

Strip:Bottom wing joint

1 FOUR-STAR 40 ARF

Instruction Book

1 Sig FOUR-STAR 40 Decal

Sheet 1

1 Sig FOUR-STAR 40 Decal Sheet 2

Additional Items Required (Not included in kit)

1 4 Channel Radio with 5

Standard Servos

1 6” Servo Extension cables

1 .40 to .50 2-Stroke motor & Muffler

or .45 to .60 4-Stroke motor &
Muffler

4 6-32 x 1-1/4” bolts, washers &

lock nuts: Motor to mount

1 Propeller to match motor

used

2 9” Medium Silicone fuel tubing 2 1cm x 8cm x 20cm Foam Rubber; for

radio packing

ASSEMBLING THE WING

The wing on the FOUR-STAR 40 ARF is designed as a strong, easy to assemble one piece unit. To avoid unnecessary
dents, dings, or scuffing of the various covered parts, we suggest that you cover your workbench with a protective blanket
or foam sheet while assembling your model.

«
1
2
3
4
5
...
»

Summary of Contents for FOUR-STAR 40 ARF

















Reviews:

No comments

Related manuals for FOUR-STAR 40 ARF

Brand: Madcow Rocketry Pages: 4

Brand: Baghera Pages: 4

Brand: ubisoft Pages: 21

Brand: REVELL Pages: 12

Brand: Radio control model Pages: 8

Brand: Badger Basket Pages: 6

Brand: Faller Pages: 8

P-3 Orion self adhesive

Brand: Eduard Pages: 3

Extra 300 PNP/BNF

Brand: PARKZONE Pages: 88

ROCKY IGED0092US

Brand: Peg-Perego Pages: 24

Brand: Smoby Pages: 7

Brand: marklin Pages: 2

Discovery micro

Brand: m2model Pages: 3

Brand: JMB-Jets Pages: 15

Techno Gears Aero Trax Plane 2.0

Brand: The Learning Journey Pages: 49

CVN-65 Enterprise Part4

Brand: Eduard Pages: 8

Brand: pitsco Pages: 162

Brand: Faller Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands