SIG Gee Bee R-2 Assembly Instructions Manual Download

Page: 1 / 6

Your kit contains the following parts. Please check your kit for any missing or damaged parts before starting construction.

COMPLETE KIT PARTS LIST

1 Plan Sheet #1

1 Plan Sheet #2

Decal Sheet

2 White Tissue

1 Colored tissue

Wire Axle's

1 Plastic Canopy

1 100" Thread

1/16"sq.x18" Balsa Strip

2 3/32"sq.x18" Balsa Strip

2 1/8"sq.x18" Balsa Strip

3/32"x3/16"x18" Balsa Strip

4 3/32"x1/4"x18" Balsa Strip

1 3/16"x3" Birch Dowel

Instruction Manual

1 9" Plastic Propeller

1 Propeller Shaft

Brass Washer

1 Nylon Propeller Bearing

2 Plastic Wheels

3/16"x60" Rubber Strip

9 Laser Cut Sheets

Tools and Building Supplies

You will need the following items to assemble this model. You must read and follow all of the manufactures
instructions provided with these items!

-Glue

CA, White Glue, Sigment or Ambroid all work well.

-Cutting Tools

A hobby knife with a #11 blade is used for general cutting. A single edge
razor blade is also a useful cutting tool.

-Clear Dope, Thinner & paint brush

-320 and 400 grit sandpaper

-Straight Pins

-Wax Paper

-Needle nose pliers

-1/4" and 1/32" Drill Bits

-Building Board

Summary of Contents for Gee Bee R-2







Search results

Summary of Contents for Gee Bee R-2

Reviews:

Related manuals for Gee Bee R-2

Brands by name

Popular brands

SIG Gee Bee R-2, Assembly Instructions Manual

Search results

Summary of Contents for Gee Bee R-2

Reviews:

Related manuals for Gee Bee R-2

Brands by name

Popular brands