background image

8

Thank you for selecting our products which have been designed and manufactured to offer you security and 
safety for many years. They have been thoroughly tested before reaching your hands, and have passed all 
necessary performance tests. All our products are covered by a 6 (SIX) years warranty, for good operation, 
from the date of purchase and covers the products that are accompanied by invoice or receipt of purchase. 
This warranty covers the free of charge repair of the device (parts and labor) in case the malfunction is due to 
failure of device itself and not if the failure is cause to any wrong installation, improper use or external factors 
such as lightning, floods, excess power voltage etc. Warranty ceases to exist if the device has been installed 
or repaired by an unauthorized person. Also, this warranty does not cover the losses, failures or injuries 
that might happen to the secured area, in case of miss operation of the device. Finally, our company is not  
responsible for the correct installation and use of the security system, for which solely responsible is the 
installer.

RECYCLING

 

   Do not dispose of this device or battery in a household waste bin!
  • The electrical and electronic equipment used must be handled separately and in    
    accordance with the legislation, which requires appropriate processing and recycling of  
    the aforesaid goods.
  • The battery contains pollutants and, therefore, after the end of its lifetime, it should not  
    be disposed of in common waste but delivered to the appropriate operator for the 
    collection and disposal of polluting waste in accordance with the local laws and 
   regulations.
  • Recycling of the product will help to avoid potential adverse effects on the environment  

   

  and human health, which could arise from inadequate waste management.

www.sigmasec.gr

You will need to check the proper functioning of the siren at regular intervals to make sure that the 

siren is not damaged and that it will work normally when needed.

The following functions should be checked in every maintenance: 

1. Check the proper operation of the siren’s speaker as well as the LED Flash by simulating an  

  alarm from the Control Panel.

2. Check the proper functioning of Tamper switch that protect the siren from opening or 

  detachment from the wall.

3. Check whether the siren’s battery voltage is 13.2-13,8 V. If the battery voltage is less than this,  

  replace the battery and plug new, ensuring the correct polarity.

4. Check for water or insect influx signs inside the siren and clean them if necessary.

Maintenance

Warranty

Summary of Contents for IRIS Lite









Reviews: