27
26
3.0. TECHNICAL DATA
Model 1A4 rev.0
Lifting dimensions mm. 3400x1500
Mass machine Kg. 19
Mass max. liftable Kg. 100
Model 1A5 rev.0
Lifting dimensions mm. 3400x1500
Mass machine Kg. 22
Mass max. liftable Kg. 150
Model 1D2 rev.0
Lifting dimensions mm. 3200x1000
Machine mass Kg. 6
Mass max. liftable Kg. 40
HOW TO PREPARE FOR WORK.
Clean and dry the tile to be lifted
Clean and dry the suction cups.
Distribute the suction cups by following the attached pictures.
Place the machine on the tile.
Press each suction cup firmly on the tile and simultaneously
actuate the lever and / or plunger.
In the case of piston actuation, it is considered a sufficient
seal when the red ring disappears.
Check visually and with your hands that all the suction cups
adhere to the tile.
When lifting a new material, leave it 5 cm high. from the
ground for at least a triple time, compared to what is neces-
sary for moving and working, to ensure that the grip stays for
a long enough time.
4.1. HANDLING PRECAUTIONS.
Lifting machine and tile bending your knees and keeping your
back vertical.
Avoid passing the suspended load over to people or places
where a possible fall in the load may be dangerous.
End-of-life cards are available on our website:
www.sigmaitalia.com
6.0. MAINTENANCE AND STORAGE.
Do not leave the machine unattended and do not allow this to
be used by strangers or incapable.
When the machine is unused, place it in such a way as to
prevent the edge of the suction cups from touching edges
that can cause permanent deformation.
If this happens, disassemble the suction cup and bathe the
rubber part in boiling water for at least 10 minutes, let it cool
down without sticking to the sealing edge.
Do not leave the machine exposed to atmospheric agents
(rain, sun, humidity, etc.).
7.0. DIAGNOSTICS.
PROBLEM
CAUSE
REMEDY
The suction cup does not remain attached to the tile.
The lip of the suction cup is damaged
Replace the suction cup
The suction cup does not remain attached to the tile.
The tile is porous
It is not possible to lift this material
The suction cup does not remain attached to the tile.
The tile is so rough that it prevents the vacuum between the suction cup
and the tile surface
Clean the surfaces in contact or ask the supplier for a suction alternative
with more material adaptation capability.
The suction cup handle does not remain hooked vertically
The handle is worn
Replace the handle
Difficult telescopic sliding of longitudinal extrusions
Dirt in the guides
Clean the guides and lubricate them with the WD40 or equivalent
lubricant
7.1 ASSISTANCE.
For any request, need or information, the user must inform the local
retailer or manufacturer of the following information:
Machine model
Year of construction
Date of purchase
Hours of service, approximate
Detailed fault information found.
7.2 MANUAL UPDATE
The manual reflects the state of the art when it is marketed, which is
an integral part of it and complies with all laws, directives, regulations in
force at that time; can not be considered inadequate only because it is
subsequently updated based on new experiences. Any modi fications,
updates, etc. which were made to the machines subsequently marketed,
do not oblige the Manufacturer to intervene on the equipment previously
supplied, nor to consider the same and the related defective and inade-
quate manual.
Any additions to the manual that the Manufacturer will deem appropriate
to send to users should be kept together with the manual that will be
included in the manual.
7.3 COLLABORATION WITH USER
The Manufacturer is at your disposal to provide additional information
and to consider suggestions for improvement to make this manual more
responsive to the requirements for which it has been prepared. If the
equipment is sold, the primary user is encouraged to report to the Builder
the address of the new user so that it can be reached with any communi-
cations and / or updates deemed necessary.
7.2. PROCESSING PROCESSING.
The Sigma-built machine has been evaluated in the design phase, and a
technical file has been set up covering all aspects of safety. At the manu-
facturing stage, all the controls necessary to ensure the perfect match of
the machine to the precision and safety standards in the technical
file are performed.
8.2. TABLES PARTS OF REPLACEMENT.
On the last pages you will find the tables of the various parts of the machi-
ne, along with their descriptions.
In case of request for spare parts, in order to avoid possible confusion
and misunderstanding, please specify the part number code that can be
detected by the board, in addition to the machine’s nameplate data.
The quantity column indicates, for each part, the total number of
identical pieces on the machine.
Each complex component is indicated on the simple components that
compose it.
9.0. WARRANTY CERTIFICATE.
Model lifting machine
1A4 / 1A5 / 1D2
The sigma company guarantees the excellent quality and perfect
functioning of the model machine.
1A4 / 1A5 / 1D2
under the following conditions:
The warranty period is 24 months from the date of sale to the end
user.
The Sigma undertakes to repair or replace for free any mechanical
parts that are found to be defective in the factory from an examination
by its technicians.
The warranty ceases to be effective when the machine or parts of it
are modified or tampered with by unauthorized personnel.
The warranty does not cover any malfunctions or malfunctions
depending on poor maintenance or improper use of the machine.
The shipping or packaging costs for the eventual return to the factory
of parts for repair or replacement and for their subsequent refund
shall be borne by the buyer.
The guarantee of good operation depends on correct application of
the instructions contained in this manual.
Refer to the information in this instruction manual:
the Manufacturer declines any liability in case of:
- Use contrary to national safety and accident law.
- wrong predisposition of lifting structures
- Failure or incorrect observance of the instructions given in this
manual.
- unauthorized modification
- Use of non-original spare parts.
- damages attributable to excessive static dynamic stresses of the
lift accessory
Place the seller’s stamp here
Write down the sales date here
Place here the signature of the seller
DECLARATION
THERE IS
OF CONFORMITY
THE MANUFACTURER
(IIA DIR. 2006/42 / EC)
Company: sigma di S. Ambrogiani & C. sas
Address: Via Gagliani 4
City: Bellaria Igea Marina
Cap: 47814
Province: RN
Country: Italy
DECLARES THAT THE MACHINE
Description: tile lift accessory
Series: (see plate 1)
Trade name - Model: KERALIFT 1A4
Year of construction: (see license plate 1)
Revision: 0
Expected use: Manual lifting of tiles
Description: tile lift accessory
Series: (see plate 1)
Trade name - Model: KERALIFT 1A5
Year of construction: (see license plate 1)
Revision: 0
Expected use: Manual lifting of tiles
Description: tile lift accessory
Series: (see plate 1)
Trade name - Model: KERALIFT 1D2
Year of construction: (see license plate 1)
Revision: 0
Expected use: Manual lifting of tiles
IS COMPLIANT WITH THE DIRECTIVES
Directive 2006/42 / EC of the European Parliament and of the Council of
17 May 2006 on machinery and amending Directive 95/16 / EC.
Reference to harmonized standards:
UNI EN ISO 12100-1 Rev. (0405) Safety of machinery - Fundamental
concepts, principles general design
AND AUTHORIZES
Name: Valter Ambrogiani
Address: Via Castellabate 18a
City: Bellaria Igea Marina
Cap: 47813
Province: RN
Country: Italy
CONSTITUTE THE TECHNICAL DOCUMENT FOR ITS ACCOUNT
Place and date of the document:
Bellaria 07/07/2016
The manufacturer
Summary of Contents for KERA-LIFT 1A4
Page 1: ...1 Manual Kera Lift...
