SignalFire Wireless I/O Module Mini Interface Manual Download

Page: 10 / 10

Rev 1.5

SignalFire Telemetry

Modbus Register Map

Technical Support and Contact Information

SignalFire Telemetry
140 Locke Dr, Suite B
Marlborough, MA, 01752
(978) 212-2868

support@signal-fire.com

Revision History

Register

Address

Description

Function

Code

Register

Type

Coils (0xxxx)

Write-only

101

00102

Relay1 Coil

Write Only

102

00103

Relay2 Coil

Write Only

111

00112

Counter1 Reset Coil

Write Only

112

00113

Counter2 Reset Coil

Write Only

Holding Registers (4xxxx)

121

40122

Relay1 Pulse (0 = Off, 1

–

65,535 = Pulse Time (sec))

Write Only

122

40123

Relay2 Pulse

Write Only

1100

41101

AI1: Voltage Reading (Unsigned int, mV)

03, 04

Read Only

1101

41102

DI1: State (Unsigned int, 1 = Closed or 0 = Open)

03, 04

Read Only

1102

41103

DI2: State

03, 04

Read Only

1103

41104

Relay #1 State (Unsigned int, 1 = ON or 0 = OFF)

03, 04

Read Only

1104

41105

Relay #2 State

03, 04

Read Only

1105

41106

AI1: Scaled Reading (Float High Word)

03, 04

Read Only

1106

41107

AI1: Scaled Reading (Float Low, Word)

03, 04

Read Only

1107

41108

DI1: Total Counts (Unsigned int, High Word)

03, 04

Read Only

1108

41109

DI1: Total Counts (Unsigned int, Low Word)

03, 04

Read Only

1109

41110

DI2: Total Counts (Unsigned int, High Word)

03, 04

Read Only

1110

41111

DI2: Total Counts (Unsigned int, Low Word)

03, 04

Read Only

1111

41112

DI1: Average Frequency (Hz x 10)

03, 04

Read Only

1112

41113

DI1: Instantaneous Frequency (Hz x 10)

03, 04

Read Only

1113

41114

DI1: Counts per minute (x 10)

03, 04

Read Only

1114

41115

DI2: Average Frequency (Hz x 10)

03, 04

Read Only

1115

41116

DI2: Instantaneous Frequency (Hz x 10)

03, 04

Read Only

1116

41117

DI1: Counts per minute (x 10)

03, 04

Read Only

Revision

Date

Changes/Updates

1.0

7/25/2019

Initial release

1.1

10/15/2019

Frequency register description

1.2

11/26/2019

Corrected mechanical drawings

1.3

1/16/2020

Corrected part number

1.4

3/5/2020

Minor corrections

1.5

4/24/2020

Added detail on mirror mode

Summary of Contents for Wireless I/O Module Mini











Search results

Summary of Contents for Wireless I/O Module Mini

Reviews:

Related manuals for Wireless I/O Module Mini

Brands by name

Popular brands

SignalFire Wireless I/O Module Mini, Interface Manual

Search results

Summary of Contents for Wireless I/O Module Mini

Reviews:

Related manuals for Wireless I/O Module Mini

Brands by name

Popular brands